Towards the ultimate goal of designing dual suspension off-road bicycles which decouple the suspension motion from the pedaling action, this study focused on determining experimentally the optimum pivot point height for a swing-arm type rear suspension such that the suspension motion was minimized. Specific objectives were (1) to determine the effect of interaction between the front and rear suspensions on the optimal pivot point height, (2) to investigate the sensitivity of the optimal height to the pedaling mechanics of the rider in both the seated and standing postures, (3) to determine the dependence of the optimal height on the rider posture. Eleven experienced subjects rode a custom-built adjustable dual suspension off-road bicycle, [Needle, S., and Hull, M. L., 1997, “An Off-Road Bicycle With Adjustable Suspension Kinematics,” Journal of Mechanical Design 119, pp. 370–375], on an inclined treadmill. The treadmill was set to a constant 6 percent grade at a constant velocity of 24.8 km/hr. With the bicycle in a fixed gear combination of 38×14, the corresponding cadence was 84 rpm. For each subject, the pivot point height was varied randomly while the motions across both the front and rear suspension elements were measured. Subjects rode in both the seated and standing postures and with the front suspension active and inactive. It was found that the power loss from the rear suspension at the optimal pivot point height was not significantly dependent on the interaction between the front and rear suspensions. In the seated posture, the optimal pivot point height was 9.8 cm on average and had a range of 8.0–12.3 cm. The average optimal pivot point height for the seated posture corresponded to an average power loss for the rear suspension that was within 10 percent of the minimum power loss for each subject for 8 of the 11 subjects. In the standing posture, the average height was 5.9 cm and ranged from 5.1–7.2 cm. The average height for the standing posture was within 10 percent of the minimum power loss for each subject for 9 of the 11 subjects. While the optimum height was relatively insensitive to pedaling mechanics in both the seated and standing postures, the choice of the optimal pivot point height in production bicycles necessitates some compromise in performance given the disparity in the averages between the seated and standing postures.
Skip Nav Destination
e-mail: mlhull@ucdavis.edu
Article navigation
February 2002
Technical Papers
Experimental Optimization of Pivot Point Height for Swing-Arm Type Rear Suspensions in Off-Road Bicycles
Ari Karchin,
Ari Karchin
Biomedical Engineering Program, University of California, Davis, CA 95616
Search for other works by this author on:
M. L. Hull
e-mail: mlhull@ucdavis.edu
M. L. Hull
Department of Mechanical Engineering and Biomedical Engineering Program, University of California, Davis, CA 95616
Search for other works by this author on:
Ari Karchin
Biomedical Engineering Program, University of California, Davis, CA 95616
M. L. Hull
Department of Mechanical Engineering and Biomedical Engineering Program, University of California, Davis, CA 95616
e-mail: mlhull@ucdavis.edu
Contributed by the Bioengineering Division for publication in the JOURNAL OF BIOMECHANICAL ENGINEERING. Manuscript received by the Bioengineering Division February 15, 2001; revision received August 16, 2001. Associate Editor: R. Vanderby, Jr.
J Biomech Eng. Feb 2002, 124(1): 101-106 (6 pages)
Published Online: August 16, 2001
Article history
Received:
February 15, 2001
Revised:
August 16, 2001
Citation
Karchin, A., and Hull, M. L. (August 16, 2001). "Experimental Optimization of Pivot Point Height for Swing-Arm Type Rear Suspensions in Off-Road Bicycles ." ASME. J Biomech Eng. February 2002; 124(1): 101–106. https://doi.org/10.1115/1.1427701
Download citation file:
Get Email Alerts
Cited By
Effect of Collagen Fiber Tortuosity Distribution on the Mechanical Response of Arterial Tissues
J Biomech Eng (February 2025)
Related Articles
Design, Build, and Test of a Bobsled Simulator for Olympic Athletes
J. Med. Devices (March,2007)
New Racing Equation for Championship Performance
J Biomech Eng (October,2000)
Bicycle Drive System Dynamics: Theory and Experimental Validation
J Biomech Eng (August,2000)
Local State Space Temporal Fluctuations: A Methodology to Reveal Changes During a Fatiguing Repetitive Task
J Biomech Eng (October,2010)
Related Proceedings Papers
Related Chapters
Introduction
Turbo/Supercharger Compressors and Turbines for Aircraft Propulsion in WWII: Theory, History and Practice—Guidance from the Past for Modern Engineers and Students
Optimization Design for 3D Roadway Based on Space Analysis of GIS
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
Rationale for Human-Powered Vehicle Design and Use
Design of Human Powered Vehicles