Spine discectomy and fusion is a widely used surgical procedure to correct irreversible degenerative diseases and injuries to the intervertebral disk. The surgical procedure involves the removal of the damage disk material, the decortication of the fusion site, and the placement of the bone graft. Fusion is believed to generate additional stresses in the neighboring disks, which can subsequently lead to new disk degeneration and re-operation. The autologous bone has proven to be the best material for the fusion. However, the autologous bone has three major disadvantages: the high rate of donor site morbidity, the limited and sometimes poor quality of the amounts of bone available, and the extra operative time needed for harvest. For these reasons this study is undertaken to estimate the optimum amount of bone graft needed for a discectomy and correlate it to the change in stress in adjacent levels. A detailed and validated 3D finite element model of the complete human cervical spine (C1-T1) was altered to simulate segmental full and partial discectomies. One full fusion (bone graft occupies about 90% of the vertebral body) and seven partial fusions (bone graft occupies about 10%, 20%, 30%, 40%, 50%, 65%, and 75% of the vertebral body) were simulated at each of the four mid- and lower single levels of the cervical spine and the relationship between the change in stresses in the adjacent levels and the bone graft size (area) was studied. The changes in stress were compared with the previously obtained results of the unfused models. The fused and unfused models were preloaded with a 73.6 N compressive force representing the weight of the head and with a 1.5 Nm physiological moment in flexion, extension, lateral bending, and axial rotation. More than 132 cases were analyzed. The results showed that the necessary amount of bone graft needed for discectomy depends on the cervical disk level to be fused and varies between 30% and 75% of the disk area. The results also suggested that there is a threshold size of the bone graft area, before and/or after which, the long-term effects of the change in stresses in adjacent disks are biomechanically consequential.
Skip Nav Destination
Article navigation
Research Papers
Stress Changes in Intervertebral Discs of the Cervical Spine Due to Partial Discectomies and Fusion
Abraham Tchako,
Abraham Tchako
Department of Mechanical Engineering,
Union College
, Schenectady, NY 12308
Search for other works by this author on:
Ali M. Sadegh
Ali M. Sadegh
Department of Mechanical Engineering,
The City College of The City University of New York
, New York, NY 10031
Search for other works by this author on:
Abraham Tchako
Department of Mechanical Engineering,
Union College
, Schenectady, NY 12308
Ali M. Sadegh
Department of Mechanical Engineering,
The City College of The City University of New York
, New York, NY 10031J Biomech Eng. May 2009, 131(5): 051013 (11 pages)
Published Online: April 15, 2009
Article history
Received:
August 2, 2007
Revised:
March 4, 2009
Published:
April 15, 2009
Citation
Tchako, A., and Sadegh, A. M. (April 15, 2009). "Stress Changes in Intervertebral Discs of the Cervical Spine Due to Partial Discectomies and Fusion." ASME. J Biomech Eng. May 2009; 131(5): 051013. https://doi.org/10.1115/1.3118763
Download citation file:
Get Email Alerts
Estimation of Joint Kinetics During Manual Material Handling Using Inertial Motion Capture: A Follow-Up Study
J Biomech Eng (February 2025)
Effect of Compressive Strain Rates on Viscoelasticity and Water Content in Intact Porcine Stomach Wall Tissues
J Biomech Eng (February 2025)
Eyelid Motion Tracking During Blinking Using High-Speed Imaging and Digital Image Correlation
J Biomech Eng (January 2025)
Related Articles
Design of a Dynamic Stabilization Spine Implant
J. Med. Devices (June,2009)
Discussion: “Stress Changes in Intervertebral Discs of the Cervical Spine Due to Partial Discectomies and Fusion” [ Tchako, A., and Sadegh, A. M., 2009, ASME J. Biomech. Eng., 131(5), p. 051013 )
J Biomech Eng (February,2010)
Influence of Cervical Disc Degeneration after Posterior Surgical Techniques in Combined Flexion-Extension—A Nonlinear Analytical Study
J Biomech Eng (February,2005)
Response to Dr. Robert W. Mann
J Biomech Eng (August,2004)
Related Proceedings Papers
Related Chapters
Subsection NB—Class 1 Components
Companion Guide to the ASME Boiler & Pressure Vessel Code, Volume 1, Second Edition
Stress Analysis of Gas Turbine Blade under Different Loads Using Finite Element Modeling
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Introduction and scope
Impedimetric Biosensors for Medical Applications: Current Progress and Challenges