Quantitative studies of material properties and interfaces using the atomic force microscope (AFM) have important applications in engineering, biotechnology, and chemistry. Contrary to what the name suggests, the AFM actually measures the displacement of a microscale probe, so one must determine the stiffness of the probe to find the force exerted on a sample. Numerous methods have been proposed for determining the spring constant of AFM cantilever probes, yet most neglect the mass of the probe tip. This work explores the effect of the tip mass on AFM calibration using the method of Sader (1995, “Method for the Calibration of Atomic Force Microscope Cantilevers,” Rev. Sci. Instrum., 66, pp. 3789) and extends that method to account for a massive, rigid tip. One can use this modified method to estimate the spring constant of a cantilever from the measured natural frequency and -factor for any mode of the probe. This may be helpful when the fundamental mode is difficult to measure or to check for inaccuracies in the calibration obtained with the fundamental mode. The error analysis presented here shows that if the tip is not considered, then the error in the static stiffness is roughly of the same order as the ratio of the tip’s mass to the cantilever beam’s. The area density of the AFM probe is also misestimated if the tip mass is not accounted for, although the trends are different. The model presented here can be used to identify the mass of a probe tip from measurements of the natural frequencies of the probe. These concepts are applied to six low spring-constant, contact-mode AFM cantilevers, and the results suggest that some of the probes are well modeled by an Euler–Bernoulli beam with a constant cross section and a rigid tip, while others are not. One probe is examined in detail, using scanning electron microscopy to quantify the size of the tip and the thickness uniformity of the probe, and laser Doppler vibrometry is used to measure the first four mode shapes. The results suggest that this probe’s thickness is significantly nonuniform, so the models upon which dynamic calibration is based may not be appropriate for this probe.
Skip Nav Destination
e-mail: msallen@engr.wisc.edu
Article navigation
November 2009
Technical Briefs
DMCMN: Experimental/Analytical Evaluation of the Effect of Tip Mass on Atomic Force Microscope Cantilever Calibration
Matthew S. Allen,
e-mail: msallen@engr.wisc.edu
Matthew S. Allen
Assistant Professor
University of Wisconsin-Madison
, 535 ERB, 1500 Engineering Drive, Madison, WI 53706
Search for other works by this author on:
Hartono Sumali,
Hartono Sumali
Principal Member of Technical Staff
Search for other works by this author on:
Peter C. Penegor
Peter C. Penegor
Undergraduate Student
Search for other works by this author on:
Matthew S. Allen
Assistant Professor
University of Wisconsin-Madison
, 535 ERB, 1500 Engineering Drive, Madison, WI 53706e-mail: msallen@engr.wisc.edu
Hartono Sumali
Principal Member of Technical Staff
Peter C. Penegor
Undergraduate Student
J. Dyn. Sys., Meas., Control. Nov 2009, 131(6): 064501 (10 pages)
Published Online: October 30, 2009
Article history
Received:
May 15, 2008
Revised:
May 7, 2009
Published:
October 30, 2009
Citation
Allen, M. S., Sumali, H., and Penegor, P. C. (October 30, 2009). "DMCMN: Experimental/Analytical Evaluation of the Effect of Tip Mass on Atomic Force Microscope Cantilever Calibration." ASME. J. Dyn. Sys., Meas., Control. November 2009; 131(6): 064501. https://doi.org/10.1115/1.4000160
Download citation file:
Get Email Alerts
Fault detection of automotive engine system based on Canonical Variate Analysis combined with Bhattacharyya Distance
J. Dyn. Sys., Meas., Control
Multi Combustor Turbine Engine Acceleration Process Control Law Design
J. Dyn. Sys., Meas., Control (July 2025)
Related Articles
Response Measurement Accuracy for Off-Resonance Excitation in Atomic Force Microscopy
J. Dyn. Sys., Meas., Control (January,2012)
Utilizing Off-Resonance and Dual-Frequency Excitation to Distinguish Attractive and Repulsive Surface Forces in Atomic Force Microscopy
J. Comput. Nonlinear Dynam (July,2011)
Influence of Local Material Properties on the Nonlinear Dynamic Behavior of an Atomic Force Microscope Probe
J. Comput. Nonlinear Dynam (October,2011)
Characterization of Intermittent Contact in Tapping-Mode Atomic Force Microscopy
J. Comput. Nonlinear Dynam (April,2006)
Related Proceedings Papers
Related Chapters
Spring Constants of Elastic Shapes in Contact
Applying the ASME Codes: Plant Piping & Pressure Vessels (Mister Mech Mentor, Vol. 2)
Elastic Constant Used in Continuum-Based Adhesion Models
International Symposium on Information Engineering and Electronic Commerce, 3rd (IEEC 2011)
4-Bit Pipeline ADC for Monolithic Active Pixel Sensors
International Conference on Advanced Computer Theory and Engineering (ICACTE 2009)