This paper reports on experimental investigations of a switched inertance hydraulic system (SIHS), which is designed to control the flow and pressure of a hydraulic supply. The switched system basically consists of a switching element, an inductance (inertance), and a capacitance. Two basic modes, a flow booster and a pressure booster, can be configured in a three-port SIHS. It is capable of boosting the pressure or flow with a corresponding drop in flow or pressure, respectively. This technique makes use of the inherent reactive behavior of hydraulic components. A high-speed rotary valve is used to provide sufficiently high switching frequency and to minimize the pressure and flow loss at the valve orifice, and a small diameter tube is used to provide an inductive effect. In this paper, a flow booster is introduced as the switched system for investigation. The measured steady-state and dynamic characteristics of the rotary valve are presented, and the dynamics characteristics of the flow booster are investigated in terms of pressure loss, flow loss, and system efficiency. The speed of sound is measured by analysis of the measured dynamic pressures in the inertance tube. A detailed analytical model of an SIHS is applied to analyze the experimental results. Experimental results on a flow booster rig show a very promising performance for the SIHS.
Skip Nav Destination
Article navigation
December 2015
Research-Article
Experimental Investigation of a Switched Inertance Hydraulic System With a High-Speed Rotary Valve
Min Pan,
Min Pan
The State Key Laboratory of Fluid Power
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
e-mail: mpan@zju.edu.cn
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
e-mail: mpan@zju.edu.cn
Search for other works by this author on:
Nigel Johnston,
Nigel Johnston
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Search for other works by this author on:
James Robertson,
James Robertson
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Search for other works by this author on:
Andrew Plummer,
Andrew Plummer
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Search for other works by this author on:
Andrew Hillis,
Andrew Hillis
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Search for other works by this author on:
Huayong Yang
Huayong Yang
The State Key Laboratory of Fluid Power
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
Search for other works by this author on:
Min Pan
The State Key Laboratory of Fluid Power
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
e-mail: mpan@zju.edu.cn
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
e-mail: mpan@zju.edu.cn
Nigel Johnston
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
James Robertson
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Andrew Plummer
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Andrew Hillis
Department of Mechanical Engineering,
University of Bath,
Bath BA2 7AY, UK
University of Bath,
Bath BA2 7AY, UK
Huayong Yang
The State Key Laboratory of Fluid Power
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
Transmission and Control,
Zhejiang University,
Hangzhou 310027, China
1Corresponding author.
Contributed by the Dynamic Systems Division of ASME for publication in the JOURNAL OF DYNAMIC SYSTEMS, MEASUREMENT, AND CONTROL. Manuscript received December 24, 2014; final manuscript received July 21, 2015; published online September 14, 2015. Assoc. Editor: Heikki Handroos.
J. Dyn. Sys., Meas., Control. Dec 2015, 137(12): 121003 (9 pages)
Published Online: September 14, 2015
Article history
Received:
December 24, 2014
Revised:
July 21, 2015
Citation
Pan, M., Johnston, N., Robertson, J., Plummer, A., Hillis, A., and Yang, H. (September 14, 2015). "Experimental Investigation of a Switched Inertance Hydraulic System With a High-Speed Rotary Valve." ASME. J. Dyn. Sys., Meas., Control. December 2015; 137(12): 121003. https://doi.org/10.1115/1.4031325
Download citation file:
Get Email Alerts
An Adaptive Sliding-Mode Observer-Based Fuzzy PI Control Method for Temperature Control of Laser Soldering Process
J. Dyn. Sys., Meas., Control
Fault detection of automotive engine system based on Canonical Variate Analysis combined with Bhattacharyya Distance
J. Dyn. Sys., Meas., Control
Multi Combustor Turbine Engine Acceleration Process Control Law Design
J. Dyn. Sys., Meas., Control (July 2025)
Related Articles
A New Model-Based Control Structure for Position Tracking in an Electro-Hydraulic Servo System With Acceleration Constraint
J. Dyn. Sys., Meas., Control (December,2017)
A Combined Variable Displacement–Digital Cylinder Hydraulic Drive for Large Presses With High Operating Frequencies
J. Dyn. Sys., Meas., Control (July,2016)
Adaptive Control of a Piezoelectric Valve for Fluid-Borne Noise Reduction in a Hydraulic Buck Converter
J. Dyn. Sys., Meas., Control (August,2017)
Modeling and Simulation of the Steady-State and Transient Performance of a Three-Way Pressure Reducing Valve
J. Dyn. Sys., Meas., Control (March,2016)
Related Chapters
The Special Characteristics of Closed-Cycle Gas Turbines
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Research of Key Technologies of the Stage Hydraulic System's Electro-Hydraulic Monitoring
International Conference on Information Technology and Management Engineering (ITME 2011)
Introduction
Hydraulic Fluids: A Guide to Selection, Test Methods and Use