In gas turbines there are many circumstances where coolant flows are introduced between the rotor disk and the stationary housing. This flow serves not only to supply coolant flow to the disk face, but also to restrict the radial inflow of hot gases to be ingested into the clearance from the turbine blade flow field. The amount of the hot radial inflow is influenced by the difference of the disk pumping capacity and the coolant flow supplied near the center. In order to cool the turbine disk with limited supply of coolant air, some means of reducing the radial inflow of hot gases is needed. It is thought that the use of different surface shapes on the stationary housing would inhibit the disk pumping capacity and, therefore, reduce the radial inflow of hot gases into the clearance. To validate the concept, an experimental study was undertaken. The basic geometry investigated was the flow field between a smooth cylindrical rotating disk parallel to a plain circular coaxial wall open to the free space at the disk periphery. Coolant flow is simulated by supplying air through the bore of the stationary wall into the gap. In addition to the base data obtained with the plain stationary wall, a duplicate series of experiments were run with an open honeycomb facing the stationary wall. The effects of the stationary wall surface geometry is assessed by comparing the data with honeycomb facing against the data with plain stationary wall. The flow field is studied through measurements of the static pressure on the stationary wall, radial and tangential velocity measurements in the clearance, the torque on the drive motor, and coolant flow rates. Flows were studied over a gap spacing to disk radii ratio of 0.01 and 0.10, disk Reynolds numbers from 5×105 to 2.2×106, and throughflow rates from 0 to 3.2 cfs. The results are presented in terms of the tangential and radial velocity profiles in the gap, the static pressure measurements, and the disk torque coefficients. The use of honeycomb on the stationary wall surface grossly altered the ingestion of external flow into the gap from the disk periphery. Important conclusions are: (1) The vacuum in the gap generated by the disk rotation is reduced by a factor of 0.4 to 0.6, depending on the radial location of the point; (2) the core tangential velocity is reduced by a factor of 0.6 to 0.7, depending on the axial spacing and the throughflow number; (3) the critical coolant flow rate is about 63 percent less for the honeycombed surface, as compared to the plain wall case. (4) for a given coolant flow rate, the penetration distance of the radial inflow is much larger for the plain disk than the honeycomb surface.
Skip Nav Destination
Article navigation
July 1986
Research Papers
Effects of Honeycomb-Shaped Walls on the Flow Regime Between a Rotating Disk and a Stationary Wall
T. Uzkan,
T. Uzkan
General Motors Corp., LaGrange, IL 60525
Search for other works by this author on:
N. J. Lipstein
N. J. Lipstein
General Electric Company, Corporate Research and Development, Schenectady, NY 12301
Search for other works by this author on:
T. Uzkan
General Motors Corp., LaGrange, IL 60525
N. J. Lipstein
General Electric Company, Corporate Research and Development, Schenectady, NY 12301
J. Eng. Gas Turbines Power. Jul 1986, 108(3): 553-561 (9 pages)
Published Online: July 1, 1986
Article history
Received:
February 7, 1986
Online:
October 15, 2009
Article
Article discussed|
View article
Connected Content
Citation
Uzkan, T., and Lipstein, N. J. (July 1, 1986). "Effects of Honeycomb-Shaped Walls on the Flow Regime Between a Rotating Disk and a Stationary Wall." ASME. J. Eng. Gas Turbines Power. July 1986; 108(3): 553–561. https://doi.org/10.1115/1.3239946
Download citation file:
Get Email Alerts
Cited By
Operation of a Compression Ignition Engine at Idling Load Under Simulated Cold Weather Conditions
J. Eng. Gas Turbines Power (August 2025)
In-Cylinder Imaging and Emissions Measurements of Cold-Start Split Injection Strategies
J. Eng. Gas Turbines Power (August 2025)
Effects of Lattice Orientation Angle on TPMS-Based Transpiration Cooling
J. Eng. Gas Turbines Power (September 2025)
Compressor Development for CO2-Based Pumped Thermal Energy Storage Systems
J. Eng. Gas Turbines Power (September 2025)
Related Articles
An Investigation of Ingress for an “Air-Cooled” Shrouded Rotating Disk System With Radial-Clearance Seals
J. Eng. Power (January,1983)
Preswirl Blade-Cooling Effectiveness in an Adiabatic Rotor–Stator System
J. Turbomach (October,1989)
Darryl E. Metzger Memorial Session Paper : A Summary of the Cooled Turbine Blade Tip Heat Transfer and Film Effectiveness Investigations Performed by Dr. D. E. Metzger
J. Turbomach (January,1995)
The Fluid Dynamics of a Shrouded Disk System With a Radial Outflow of Coolant
J. Eng. Power (July,1970)
Related Proceedings Papers
Related Chapters
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Combined Cycle Power Plant
Energy and Power Generation Handbook: Established and Emerging Technologies
Fans and Air Handling Systems
Thermal Management of Telecommunications Equipment