Rotordynamic-coefficient and leakage test results are presented for three grooved seals with helix angles of 0, 15, and 30 deg against rotation. The seals are 50.8 mm long and 152.4 mm in diameter. Tests were done for two supply pressures (up to 17 bars), three speeds (5000, 12,000, and 16,000 rpm), four pressure ratios, and three inlet fluid prerotation conditions. The results showed that increasing the helix angle yields a progressive reduction in the cross-coupled stiffness coefficient k and a progressive increase in leakage. The helically grooved seals consistently yield negative cross-coupled stiffness coefficients for nonprerotated inlet flow; hence, k in these seals would oppose forward whirl of a rotor. Helically grooved seals become less effective at reducing k with increasing preswirl; hence, for optimum effectiveness they should be used with a swirl brake. Comparison between helically grooved and honeycomb-stator seals showed that helically grooved stators had reduced (negative) whirl-frequency ratios for nonprerotated flows but were no better than honeycomb-stator seals for elevated fluid prerotation. The 15 and 30 deg helix grooves leaked about 1.6 and 2.2 times, respectively, as much as the honeycomb-stator seals.
Skip Nav Destination
Article navigation
April 1996
Research Papers
Experimental Leakage and Rotordynamic Results for Helically Grooved Annular Gas Seals
D. W. Childs,
D. W. Childs
Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843
Search for other works by this author on:
A. J. Gansle
A. J. Gansle
Sanden International (U.S.A.), Inc., Wylie, TX 75098
Search for other works by this author on:
D. W. Childs
Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843
A. J. Gansle
Sanden International (U.S.A.), Inc., Wylie, TX 75098
J. Eng. Gas Turbines Power. Apr 1996, 118(2): 389-393 (5 pages)
Published Online: April 1, 1996
Article history
Received:
February 13, 1995
Online:
November 19, 2007
Citation
Childs, D. W., and Gansle, A. J. (April 1, 1996). "Experimental Leakage and Rotordynamic Results for Helically Grooved Annular Gas Seals." ASME. J. Eng. Gas Turbines Power. April 1996; 118(2): 389–393. https://doi.org/10.1115/1.2816601
Download citation file:
Get Email Alerts
Cited By
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Theory Versus Experiment for the Rotordynamic Characteristics of a High Pressure Honeycomb Annular Gas Seal at Eccentric Positions
J. Tribol (April,2003)
Swirl Brake Design for Improved Rotordynamic Vibration Stability Based on Computational Fluid Dynamics System Level Modeling
ASME Open J. Engineering (January,2023)
The Effects of Converging and Diverging Axial Taper on the Rotordynamic Coefficients of Liquid Annular Pressure Seals: Theory Versus Experiment
J. Vib. Acoust (April,2000)
Improving the Stability of Labyrinth Gas Seals
J. Eng. Gas Turbines Power (April,2001)
Related Proceedings Papers
Related Chapters
Pressure Testing
Process Piping: The Complete Guide to ASME B31.3, Third Edition
Re-entrant Gas Flows of High-speed Ventilated Supercavity
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Pipeline Integrity and Security
Continuing and Changing Priorities of the ASME Boiler & Pressure Vessel Codes and Standards