A combined experimental and numerical study of interaction between cooling flow and mainstream gas flow in a turbine rotor-stator rim cavity is reported. Particular emphasis is put on the flow phenomena in a rim cavity downstream of rotor blades. The experiments are conducted on a rig simulating an engine HP-turbine in which cooling effectiveness distributions as well as velocities, turbulence quantities, pressure, and temperature profiles are measured. Numerical calculation, especially at a full 3D, unsteady solution level, can lead to satisfactory predictions in fluid and mass transfer inside the cavity. Both experimental and numerical results indicate that large turbulence stresses near the rotor disk intensify turbulent diffusion across the cavity and consequently axial distribution of the cooling effectiveness inside the cavity becomes uniform. In order to obtain an adequate distribution of cooling effectiveness across the rim cavity and to suppress the turbulence level near the rotor surface for more efficient cooling, a novel cooling method is developed using numerical simulation. The disk-front and -rear cavities are then redesigned according to the new cooling strategy and integrated in the test rig. Experimental results verify a significant advance in cooling performance with the new method.
Skip Nav Destination
Article navigation
October 2005
Technical Papers
A Novel Cooling Method for Turbine Rotor-Stator Rim Cavities Affected by Mainstream Ingress
Y. Okita,
Y. Okita
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
Search for other works by this author on:
M. Nishiura,
M. Nishiura
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
Search for other works by this author on:
S. Yamawaki,
S. Yamawaki
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
Search for other works by this author on:
Y. Hironaka
Y. Hironaka
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
Search for other works by this author on:
Y. Okita
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
M. Nishiura
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
S. Yamawaki
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, Japan
Y. Hironaka
Aero-Engine and Space Operations,
Ishikawajima-Harima Heavy Industries (IHI)
, Tokyo, JapanJ. Eng. Gas Turbines Power. Oct 2005, 127(4): 798-806 (9 pages)
Published Online: March 1, 2004
Article history
Received:
October 1, 2003
Revised:
March 1, 2004
Citation
Okita, Y., Nishiura, M., Yamawaki, S., and Hironaka, Y. (March 1, 2004). "A Novel Cooling Method for Turbine Rotor-Stator Rim Cavities Affected by Mainstream Ingress." ASME. J. Eng. Gas Turbines Power. October 2005; 127(4): 798–806. https://doi.org/10.1115/1.1925647
Download citation file:
Get Email Alerts
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Influence of Fluid Dynamics on Heat Transfer in a Preswirl Rotating-Disk System
J. Eng. Gas Turbines Power (October,2005)
Prediction of Film Cooling and Heat Transfer on a Rotating Blade Platform With Stator-Rotor Purge and Discrete Film-Hole Flows in a 1 - 1 2 Turbine Stage
J. Turbomach (October,2009)
Film-Cooling Effectiveness on a Rotating Turbine Platform Using Pressure Sensitive Paint Technique
J. Turbomach (October,2010)
Related Proceedings Papers
Related Chapters
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Introduction
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential