Abstract

Gas foil bearings (FB) satisfy many of the requirements noted for novel oil-free turbomachinery. However, FB design remains largely empirical, in spite of successful commercial applications. The mechanical structural characteristics of foil bearings, namely stiffness and damping, have been largely ignored in the archival literature. Four commercial bump-type foil bearings were acquired to measure their load capacity under conditions of no shaft rotation. The test bearings contain a single Teflon-coated foil supported on 25 bumps. The nominal radial clearance is 0.036mm for a 38mm journal. A simple test setup was assembled to measure the FB deflections resulting from static loads. The tests were conducted with three shafts of increasing diameter to induce a degree of preload into the FB structure. Static measurements show nonlinear FB deflections, varying with the orientation of the load relative to the foil spot weld. Loading and unloading tests evidence hysteresis. The FB structural stiffness increases as the bumps-foil radial deflection increases (hardening effect). The assembly preload results in notable stiffness changes, in particular for small radial loads. A simple analytical model assembles individual bump stiffnesses and renders predictions for the FB structural stiffness as a function of the bump geometry and material, dry-friction coefficient, load orientation, clearance and preload. The model predicts well the test data, including the hardening effect. The uncertainty in the actual clearance (gap) upon assembly of a shaft into a FB affects most of the predictions.

1.
Agrawal
,
G. L.
, 1997, “
Foil Air∕Gas Bearing Technology—An Overview
,”
International Gas Turbine & Aeroengine Congress & Exhibition
, Orlando, Florida, ASME Paper No. 97-GT-347.
2.
Heshmat
,
H.
,
Walomit
,
J.
, and
Pinkus
,
O.
, 1983, “
Analysis of Gas-Lubricated Compliant Journal Bearings
,”
ASME J. Lubr. Technol.
0022-2305,
105
, pp.
647
655
.
3.
Peng
,
J.-P.
, and
Carpino
,
M.
, 1993, “
Calculation of Stiffness and Damping Coefficient for Elastically Supported Gas Foil Bearings
,”
ASME J. Tribol.
0742-4787,
115
, pp.
20
27
.
4.
Ku
,
C.-P.
, and
Heshmat
,
H.
, 1992, “
Complaint Foil Bearing Structural Stiffness Analysis Part I: Theoretical Model—Including Strip and Variable Bump Foil Geometry
,”
ASME J. Tribol.
0742-4787,
114
, pp.
394
400
.
5.
Ku
,
C.-P.
, and
Heshmat
,
H.
, 1993, “
Complaint Foil Bearing Structural Stiffness Analysis Part II: Experimental Investigation
,”
ASME J. Tribol.
0742-4787,
113
, pp.
364
369
.
6.
Iordanoff
,
I.
, 1999, “
Analysis of an Aerodynamic Complaint Foil Thrust Bearing: Method for a Rapid Design
,”
ASME J. Tribol.
0742-4787,
121
, pp.
816
822
.
7.
Ku
,
C.-P.
, and
Heshmat
,
H.
, 1994, “
Structural Stiffness and Coulomb Damping in Compliant Foil Journal Bearing: Theoretical Considerations
,”
STLE Tribol. Trans.
1040-2004,
37
, pp.
525
533
.
8.
Ku
,
C.-P.
, and
Heshmat
,
H.
, 1994, “
Structural Stiffness and Coulomb Damping in Compliant Foil Journal Bearing: Parametric Studies
,”
STLE Tribol. Trans.
1040-2004,
37
, pp.
455
462
.
9.
Agrawal
,
G. L.
, 1998, “
Foil Air Bearings Cleared to Land
,”
Mech. Eng. (Am. Soc. Mech. Eng.)
0025-6501,
120
July, pp.
78
80
.
10.
DellaCorte
,
C.
,
Fellenstein
,
J. A.
, and
Benoy
,
P.
, 1999, “
Evaluation of Advanced Solid Lubricant Coatings for Foil Air Bearings Operating at 25° and 500°C
,”
STLE Tribol. Trans.
1040-2004,
42
, pp.
338
342
.
11.
DellaCorte
,
C.
, and
Valco
,
M.
, 2000, “
Load Capacity Estimation of Foil Air Journal Bearing for Oil-Free Turbomachinery Applications
,”
STLE Tribol. Trans.
1040-2004,
43
, pp.
795
801
.
12.
Ku
,
C.-P. R.
, 1993, “
An Experimental and Theoretical Study of the Dynamic Structural Stiffness in Compliant Foil Journal Bearings
,”
ASME 14th Biennial Conference on Mechanical Vibration and Noise
, Albuquerque, NM, DE-Vol.
63
,
Vibration of Mechanical Systems and the History of Mechanical Design
, pp.
83
88
.
13.
Ku.
,
C.
, and
Heshmat
,
H.
, 1994, “
Effect of Static Load on Dynamic Structural Properties in a Flexible Supported Foil Journal Bearing
,”
ASME J. Vibr. Acoust.
0739-3717,
116
, pp.
257
262
.
14.
Radil
,
K.
,
Howard
,
S.
, and
Dykas
,
B.
, 2002, “
The Role of Radial Clearance on the Performance of Foil Air Bearings
,”
STLE Tribol. Trans.
1040-2004,
45
, pp.
485
490
.
15.
DellaCorte
,
C.
, and
Valco
,
M.
, 2000, “
Load Capacity Estimation of Foil Air Journal Bearings for Oil-Free Turbomachinery Applications
,”
STLE Tribol. Trans.
1040-2004,
43
, pp.
795
801
.
16.
Rubio
,
D.
, “
Measurement of Static Structural Stiffness of Bump-Type Foil Gas Bearings
,” Undergraduate Senior Honor thesis, Texas A&M University, Mechanical Engineering Department, August 2002.
17.
Lu
,
Y. P.
, and
Sun
,
C. T.
, 1995,
Vibration Damping of Structural Elements
,
Prentice–Hall
, Englewood Cliffs, pp.
6
7
.
18.
Salehi
,
M.
,
Heshmat
,
H.
, and
Walton
,
J.
, 2003, “
On the Frictional Damping Characterization of Compliant Bump Foils
,”
ASME J. Tribol.
0742-4787,
125
, pp.
804
813
.
You do not currently have access to this content.