Extensive work performed by Capstone Turbine Corporation, Oak Ridge National Laboratory, and various others has shown that the traditional primary surface recuperator alloy, type 347 stainless steel, is unsuitable for applications above . Numerous studies have shown that the presence of water vapor greatly accelerates the oxidation rate of type 347 stainless steel at temperatures above . Water vapor is present as a product of combustion in the microturbine exhaust, making it necessary to find replacement alloys for type 347 stainless steel that will meet the long life requirements of microturbine primary surface recuperators. It has been well established over the past few years that alloys with higher chromium and nickel contents than type 347 stainless steel have much greater oxidation resistance in the microturbine environment. One such alloy that has replaced type 347 stainless steel in primary surface recuperators is Haynes Alloy HR-120 (Haynes and HR-120 are trademarks of Haynes International, Inc.), a solid-solution-strengthened alloy with nominally 33 wt % Fe, 37 wt % Ni and 25 wt % Cr. Unfortunately, while HR-120 is significantly more oxidation resistant in the microturbine environment, it is also a much more expensive alloy. In the interest of cost reduction, other candidate primary surface recuperator alloys are being investigated as possible alternatives to type 347 stainless steel. An initial rainbow recuperator test has been performed at Capstone to compare the oxidation resistance of type 347 stainless steel, HR-120, and the Allegheny Ludlum austenitic alloy AL (AL 20–25+Nb is a trademark of ATI Properties, Inc. and is licensed to Allegheny Ludlum Corporation). Evaluation of surface oxide scale formation and associated alloy depletion and other compositional changes has been carried out at Oak Ridge National Laboratory. The results of this initial rainbow test will be presented and discussed in this paper.
Skip Nav Destination
Article navigation
February 2010
Research Papers
Comparison of Three Microturbine Primary Surface Recuperator Alloys
Wendy J. Matthews,
Wendy J. Matthews
Capstone Turbine Corporation
, Chatsworth, CA 91311
Search for other works by this author on:
Karren L. More,
Karren L. More
Oak Ridge National Laboratory
, Oak Ridge, TN 37831
Search for other works by this author on:
Larry R. Walker
Larry R. Walker
Oak Ridge National Laboratory
, Oak Ridge, TN 37831
Search for other works by this author on:
Wendy J. Matthews
Capstone Turbine Corporation
, Chatsworth, CA 91311
Karren L. More
Oak Ridge National Laboratory
, Oak Ridge, TN 37831
Larry R. Walker
Oak Ridge National Laboratory
, Oak Ridge, TN 37831J. Eng. Gas Turbines Power. Feb 2010, 132(2): 022302 (6 pages)
Published Online: November 5, 2009
Article history
Received:
March 19, 2009
Revised:
March 23, 2009
Online:
November 5, 2009
Published:
November 5, 2009
Citation
Matthews, W. J., More, K. L., and Walker, L. R. (November 5, 2009). "Comparison of Three Microturbine Primary Surface Recuperator Alloys." ASME. J. Eng. Gas Turbines Power. February 2010; 132(2): 022302. https://doi.org/10.1115/1.3157094
Download citation file:
Get Email Alerts
Cited By
Numerical Investigation of CO and NO Production From Premixed Hydrogen/Methane Fuel Blends
J. Eng. Gas Turbines Power (April 2025)
An Efficient Uncertainty Quantification Method Based on Inter-Blade Decoupling for Compressors
J. Eng. Gas Turbines Power (April 2025)
Experimental Design Validation of a Swirl-Stabilized Burner With Fluidically Variable Swirl Number
J. Eng. Gas Turbines Power (April 2025)
Experimental Characterization of a Bladeless Air Compressor
J. Eng. Gas Turbines Power (April 2025)
Related Articles
Creep Strength and Microstructure of AL 20 - 25 + Nb Alloy Sheets and Foils for Advanced Microturbine Recuperators
J. Eng. Gas Turbines Power (July,2007)
Primary Surface Recuperator Alloy Oxidation: A Comparison of Accelerated Engine Testing to Field Operation
J. Eng. Gas Turbines Power (April,2011)
Long-Term Microturbine Exposure of an Advanced Alloy for Microturbine Primary Surface Recuperators
J. Eng. Gas Turbines Power (May,2009)
Field and Laboratory Evaluations of Commercial and Next-Generation Alumina-Forming Austenitic Foil for Advanced Recuperators
J. Eng. Gas Turbines Power (December,2016)
Related Proceedings Papers
Related Chapters
E110opt Fuel Cladding Corrosion under PWR Conditions
Zirconium in the Nuclear Industry: 20th International Symposium
Lay-Up and Start-Up Practices
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential