Vertically aligned carbon nanotube (VACNT) films with high thermal conductance and mechanical compliance offer an attractive combination of properties for thermal interface applications. In current work, VACNT films synthesized by the chemical vapor deposition method were used as thermal interface material (TIM) and investigated experimentally. The liquid metal alloy (LMA) with melting point of 59 °C was used as bonding material to attach VACNT films onto copper plates. In order to enhance the contact area of LMA with the contact surface, the wettability of the contact surface was modified by plasma treatment. The thermal diffusivity, thermal conductivity, and thermal resistance of the synthesized samples were measured and calculated by the laser flash analysis (LFA) method. Results showed that: (1) VACNT films can be used as TIM to enhance the heat transfer performance of the contact surface; (2) the LMA can be used as bonding material, and its performance is dependent on the LMA wettability on the contact surface. (3) When applying VACNT film as the TIM, LMA is used as the bonding material. After plasma treatment, comparison of VACNT films with the dry contact between copper and silicon showed that thermal diffusivity can be increased by about 160%, the thermal conductivity can be increased by about 100%, and the thermal resistance can be decreased by about 31%. This study shows the advantages of using VACNT films as TIMs in microelectronic packaging.
Skip Nav Destination
Article navigation
September 2015
This article was originally published in
Journal of Heat Transfer
Research-Article
Investigation on Carbon Nanotubes as Thermal Interface Material Bonded With Liquid Metal Alloy
Yulong Ji,
Yulong Ji
Associate Professor
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
e-mails: jiyulong@dlmu.edu.cn; jiyulongcn@163.com
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
e-mails: jiyulong@dlmu.edu.cn; jiyulongcn@163.com
Search for other works by this author on:
Gen Li,
Gen Li
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Search for other works by this author on:
Chao Chang,
Chao Chang
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Search for other works by this author on:
Yuqing Sun,
Yuqing Sun
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Search for other works by this author on:
Hongbin Ma
Hongbin Ma
Department of Mechanical
and Aerospace Engineering,
University of Missouri,
Columbia, MO 65211
and Aerospace Engineering,
University of Missouri,
Columbia, MO 65211
Search for other works by this author on:
Yulong Ji
Associate Professor
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
e-mails: jiyulong@dlmu.edu.cn; jiyulongcn@163.com
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
e-mails: jiyulong@dlmu.edu.cn; jiyulongcn@163.com
Gen Li
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Chao Chang
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Yuqing Sun
Marine Engineering College,
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Dalian Maritime University,
Dalian, Liaoning Province 116026, China
Hongbin Ma
Department of Mechanical
and Aerospace Engineering,
University of Missouri,
Columbia, MO 65211
and Aerospace Engineering,
University of Missouri,
Columbia, MO 65211
1Corresponding author.
Manuscript received April 29, 2014; final manuscript received August 11, 2014; published online May 14, 2015. Assoc. Editor: Yogesh Jaluria.
J. Heat Transfer. Sep 2015, 137(9): 091017 (9 pages)
Published Online: May 14, 2015
Article history
Received:
April 29, 2014
Revision Received:
August 11, 2014
Citation
Ji, Y., Li, G., Chang, C., Sun, Y., and Ma, H. (May 14, 2015). "Investigation on Carbon Nanotubes as Thermal Interface Material Bonded With Liquid Metal Alloy." ASME. J. Heat Transfer. September 2015; 137(9): 091017. https://doi.org/10.1115/1.4030233
Download citation file:
Get Email Alerts
Cited By
The Effect of Biot Number on a Generalized Heat Conduction Solution
J. Heat Mass Transfer
Numerical Investigation of Conjugate Natural Convection From a Vertical Cylindrical Open Cavity
J. Heat Mass Transfer (August 2023)
Heat Transfer and Pressure Loss of Turbulent Flow in a Wedge-Shaped Cooling Channel With Different Types of Triply Periodic Minimal Surfaces
J. Heat Mass Transfer (September 2023)
Related Articles
Effects of Growth Temperature on Carbon Nanotube Array Thermal Interfaces
J. Heat Transfer (November,2008)
3-Omega Measurements of Vertically Oriented Carbon Nanotubes on Silicon
J. Heat Transfer (November,2006)
Heat Dissipation System Based on Electromagnetic-Driven Rotational Flow of Liquid Metal Coolant
J. Thermal Sci. Eng. Appl (December,2021)
An Experimental Investigation in the Performance of Water-Filled Silicon Microheat Pipe Arrays
J. Electron. Packag (June,2010)
Related Proceedings Papers
Related Chapters
Simulation of Plasma Discharges in Plasma Enhanced Chemical Vapor Deposition for Microcrystalline Silicon Films
International Conference on Electronics, Information and Communication Engineering (EICE 2012)
Theoretical Analysis of Laminar Heat Transfer Performance of Liquid Metal with Low Melting Point
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3