Point Laser Triangulation (PLT) probes have significant advantages over traditional touch probes. These advantages include throughput and no contact force, which motivate use of PLT probes on Coordinate Measuring Machines (CMMs). This document addresses the problem of extrinsic calibration. We present a precise technique for calibrating a PLT probe to a CMM. This new method uses known information from a localized polyhedron and measurements taken on the polyhedron by the PLT probe to determine the calibration parameters. With increasing interest in applying PLT probes for point measurements in coordinate metrology, such a calibration method is needed. [S1087-1357(00)01703-2]
Issue Section:
Technical Briefs
1.
Hayati, S. A., 1983, “Robot arm geometric link parameter estimation,” 22nd IEEE Control System Society Conference on Decision and Control (San Antonio, Texas), Vol. 3, No. 7, pp. 1477–1483.
2.
Menq, C. H., and Borm, J. H., 1988, “Estimation and observability measure of parameter errors in a robot kinematic model,” Proceedings of U.S.A.-Japan Symposium on Flexible Automation (Minneapolis, July 18–20), pp. 65–70.
3.
Borm
, J. H.
, and Menq
, C. H.
, 1991
, “Determination of optimal measurement configurations for robot calibration based on observability measure
,” Int. J. Robot. Res.
, 10
, No. 1
, pp. 51
–63
.4.
Hocken, R. J., 1980, “Technology of machine tools, Vol. 5, Machine tool accuracy,” Machine Tool Task Force.
5.
Ni
, J.
, 1997
, “CNC machine accuracy enhancement through real-time error compensation
,” Trans. ASME, J. Manuf. Sci. Eng.
, 119
, pp. 717
–725
.6.
Lee
, E. S.
, Suh
, S. H.
, and Shon
, J. W.
, 1998
, “Comprehensive method for the calibration of volumetric positioning accuracy of CNC-machines
,” Int. J. Adv. Manufac. Technol. (Springer-Verlag London Ltd., London Engl.)
, 119
, No. 1
, pp. 43
–49
.7.
Chen, J., and Chen, Y. F., 1987, “Estimation of coordinate measuring machine error parameters,” Proceedings of IEEE International Conference on Robotics and Automation (San Francisco), pp. 1011–1016, Apr. 7–10.
8.
Chen
, Y. D.
, and Ni
, J.
, 1993
, “Dynamic calibration and compensation of a 3-D laser radar scanning system
,” IEEE Trans. Rob. Autom.
, 9
, No. 3
, pp. 318
–322
.9.
Agin, G. J., 1985, “Calibration and use of a light stripe range sensor mounted on the hand of a robot,” Proceedings of the IEEE International Conference on Robotics and Automation, St. Louis.
10.
Chen, C., H., and Kak, A. C., 1987, “Modeling and calibration of a structured light scanner for 3-D robot vision,” Proceedings of the 1987 IEEE International Conference on Robotics and Automation, CH2413-3., pp. 807–815.
11.
Agin, G. J., and Highnam, P. T., 1987, “Movable light-strip sensor for obtaining three-dimensional coordinate measurement,” Proceedings of the SPIE International Tech. Sym., San Diego, CA, pp. 326–333, Aug. 21–27.
12.
Che
, C.
, and Ni
, J.
, 1996
, “Modeling and calibration of a structured-light optical CMM via skewed frame representation
,” Trans. ASME, J. Manufact. Sci. Eng.
, 118
, pp. 595
–603
.13.
Hu, W. 1995, “3-D surface digitizing using coordinate measuring machines (CMM) with laser displacement sensors (LDS),” Master’s thesis, Dept. of Electrical Engineering, The Ohio State University.
14.
Sahoo
, K. C.
, and Menq
, C. H.
, 1991
, “Localization of 3-D objects having complex sculptured surfaces using tactile sensing and surface description
,” ASME J. Eng. Ind.
, 523
, pp. 85
–92
.15.
Gunnarsson
, K. T.
, and Prinz
, F. B.
, 1987
, “CAD model-based localization of parts in manufacturing
,” IEEE Comput.
, 20
, pp. 66
–74
. Copyright © 2000
by ASME
You do not currently have access to this content.