During a variety of high-speed cutting operations that can include both laser and traditional saw methods, full workpiece support is not always practical or even possible. As a result, costly premature fractures and associated damage such as chips, burrs, and cracks (micro- to macroscale) can result. In most instances, the resulting stresses are primarily mechanical in nature and arise from the bending and∕or twisting moments from the still attached scrap. Under these conditions, mixed-mode fracture is all but inevitable since the supporting section is continuously diminishing as the cut progresses. Given these conditions, it is conceivable that intentionally induced compressive-stresses due to an off-focus laser might be used to control (or at least, delay) such fractures. In this paper, a technique of using a tailored CO2 laser-heating scenario ahead of a progressing cut to “actively” induce compressive thermoelastic stresses to control fracture of a cantilevered plate was developed with guidance from numerical simulations. Simulations of the active-stressing approach were achieved by using a customized finite-element formulation that was previously employed to model dual-beam laser machining. However, in this instance probabilistic fracture-mechanics was used to quantify the influence of the induced compressive-stresses on the time and nature of the fracture. Experiments were also conducted to test the feasibility of the active-stressing approach. The effect of important parameters such as the beam diameter, incident power density, and the positioning of the second beam with respect to the progressing cut was then studied with the goal of reducing and∕or delaying the likelihood of fracture.

1.
Chryssolouris
,
G.
,
Anifantis
,
G.
, and
Karagiannis
,
N. S.
, 1997, “
Laser Assisted Machining: An Overview
,”
ASME J. Manuf. Sci. Eng.
1087-1357,
119
, pp.
766
769
.
2.
McDermott
,
K.
,
Tillotson
,
J.
, and
Phoenix
,
R. C.
, 1988, “
Thick and Thin Film Manufacturers Find Laser Machining Cost Effective
,”
Hybrid Circuit Technology
,
5
, pp.
121
134
.
3.
Powell
,
J.
, 1988,
CO2 Laser Cutting
, 2nd ed.,
Springer
,
London
.
4.
Black
,
I.
, 1998, “
Laser Cutting Speeds for Ceramic Tile: A Theoretical-Empirical Comparison
,”
Opt. Laser Technol.
0030-3992,
30
, pp.
95
101
.
5.
Gross
,
T. S.
,
Hening
,
S. D.
, and
Watt
,
D. W.
, 1991, “
Crack Formation During Laser Cutting of Silicon
,”
J. Appl. Phys.
0021-8979,
69
, pp.
983
989
.
6.
Smith
,
R.
,
Surprenant
,
N.
, and
Kaminski
,
D. A.
, 1991, “
Fracture Characteristics of an Alumina Oxide Ceramic During Continuous Wave Carbon Dioxide Laser Cutting
,”
ICALEO
, Nov. 3–8, pp.
337
347
.
7.
Zhang
,
J. H.
,
Lee
,
T. C.
,
Ai
,
X.
, and
Lau
,
W. S.
, 1996, “
Investigation of the Surface Integrity of Laser-Cut Ceramic
,”
J. Mater. Process. Technol.
0924-0136,
57
, pp.
304
310
.
8.
Li
,
K.
, 1995, “
Plane Stress Model for Fracture of Ceramics During Laser Cutting
,”
Int. J. Mach. Tools Manuf.
0890-6955,
35
, pp.
1493
1506
.
9.
Lumley
,
R. M.
, 1969, “
Controlled Separation of Brittle Materials Using a Laser
,”
Bull. Am. Ceram. Soc.
0002-7812,
48
, pp.
850
854
.
10.
Garibotti
,
D. J.
, 1963, “
Dicing of Micro-Semiconductors
,” U.S. Patent No. 3,112,850.
11.
Morita
,
N.
,
Ishida
,
S.
,
Fujimori
,
Y.
, and
Ishikawa
,
K.
, 1988, “
Pulsed Laser Processing of Ceramics in Water
,”
Appl. Phys. Lett.
,
52
, pp.
201
209
.
12.
Hong
,
L.
, 2002, “
Investigation of Cutting of Engineering Ceramics With Q-Switched Pulsed CO2 Laser
,”
Opt. Lasers Eng.
0143-8166,
38
, pp.
279
289
.
13.
Hong
,
L.
, 1999, “
A Study of Laser Cutting Engineering Ceramics
,”
Opt. Laser Technol.
0030-3992,
31
, pp.
531
538
.
14.
Tonoshof
,
H. K.
, and
Gonoschior
,
M.
, 1992, “
Reduction of Crack Damage in Laser Cutting of Ceramics
,”
Proceedings of the LAMP ’92, Laser Advanced Materials Processing
,
2
, pp.
645
650
.
15.
Quintero
,
F.
,
Pou
,
F.
,
Lusquinos
,
M.
,
Larosi
,
R.
,
Soto
,
R.
, and
Perez-Amor
,
M.
, 2001, “
Cutting of Ceramic Plates by Fiber-Optic Guided Nd:YAG Laser
,”
J. Laser Appl.
1042-346X,
13
, pp.
84
92
.
16.
Tuersley
,
I. P.
,
Hoult
,
T. P.
, and
Pashby
,
I. R.
, 1998, “
The Processing of SiC∕SiC Ceramic Matrix Composites Using a Pulsed Nd:YAG Laser, Part II: The Effects of Process Variables
,”
Opt. Lasers Eng.
0143-8166,
33
, pp.
963
971
.
17.
Segall
,
A. E.
,
Cai
,
G.
,
Akarapu
,
R.
,
Romasco
,
A.
, and
Li
,
B. Q.
, 2005, “
Fracture Control of Unsupported Ceramics During Laser Machining Using a Simultaneous Prescore
,”
J. Laser Appl.
1042-346X,
17
, pp.
57
62
.
18.
Akarapu
,
R.
, and
Segall
,
A. E.
, 2006, “
Numerical Simulations of an Active-Stressing Technique for Delaying Fracture During Cutting of Alumina
,”
ASME J. Manuf. Sci. Eng.
1087-1357,
128
(
4
), pp.
921
927
.
19.
W. D.
Kingery
, 1960,
Introduction to Ceramics
,
ASME
,
New York
.
20.
Akarapu
,
R.
,
Li
,
B. Q.
, and
Segall
,
A. E.
, 2003, “
Finite Element Modeling of Ablation Phenomena and Thermal Stress Evolution During a Unique Application of Dual Laser Cutting of Ceramics
,”
Proceedings of TMS Annual Conference
,
San Diego, CA
, pp.
87
98
.
21.
Akarapu
,
R.
,
Li
,
B. Q.
, and
Segall
,
A. E.
, 2003, “
A 3-D Numerical Model for Ablation Phenomena and Thermal Stress Evolution During Laser Machining
,”
Proceedings of ASME Summer Heat Transfer Conference
,
Las Vegas, NV
, Paper No. HT2003-40298.
22.
Nemeth
,
N. N.
,
Powers
,
L. P.
,
Janosik
,
L. A.
, and
Gyekenyesi
,
J. P.
, 2003, “
CARES∕LIFE Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program
,” NASA∕TM, Report No. 106316.
23.
Cai
,
L.
, and
Sheng
,
P.
, 1994, “
Analysis of Laser Evaporative and Fusion Cutting
,” ASME, Production Engineering Division, Vol.
68
(
1
), pp.
469
480
.
You do not currently have access to this content.