A primary consideration in the welding of structures for service in Canadian offshore and arctic regions is the toughness of weld metals required at very low ambient temperatures (−30°C to −60°C). To assess the suitability of cored wires for applications in these environments, some currently available commercial consumables for the flux-cored arc welding (FCAW) process were evaluated. Cored wires belonging to four different categories: basic, rutile, metal-cored and innershield, were used to prepare welds with similar welding procedures. Weld metal Charpy V-notch (CVN) and crack tip opening displacement (CTOD) tests were carried out and the effect of weld metal composition, microstructure and inclusion content in the weld metal toughness was examined. The Charpy transition temperatures and the CTOD toughness results indicated that, of the 16 wires tested, there were only seven that would be suitable for critical applications.
Skip Nav Destination
Article navigation
February 1993
Research Papers
Evaluation of FCAW Consumables for Offshore and Arctic Structure Fabrication
S. R. Bala,
S. R. Bala
Welding Institute of Canada, Oakville, Ontario, Canada
Search for other works by this author on:
L. Malik,
L. Malik
Fleet Technology Ltd., Kanata, Ontario, Canada
Search for other works by this author on:
J. E. M. Braid
J. E. M. Braid
Metals Technology Laboratories, CANMET, Ottawa, Ontario, Canada
Search for other works by this author on:
S. R. Bala
Welding Institute of Canada, Oakville, Ontario, Canada
L. Malik
Fleet Technology Ltd., Kanata, Ontario, Canada
J. E. M. Braid
Metals Technology Laboratories, CANMET, Ottawa, Ontario, Canada
J. Offshore Mech. Arct. Eng. Feb 1993, 115(1): 76-82 (7 pages)
Published Online: February 1, 1993
Article history
Received:
July 24, 1990
Revised:
July 7, 1992
Online:
June 12, 2008
Citation
Bala, S. R., Malik, L., and Braid, J. E. M. (February 1, 1993). "Evaluation of FCAW Consumables for Offshore and Arctic Structure Fabrication." ASME. J. Offshore Mech. Arct. Eng. February 1993; 115(1): 76–82. https://doi.org/10.1115/1.2920094
Download citation file:
Get Email Alerts
Cited By
Numerical Modeling of Fish Cage Structural Responses in Regular and Irregular Waves Using Modified XPBD
J. Offshore Mech. Arct. Eng (April 2025)
Layout Optimization of Wave Energy Park Based on Multi-Objective Optimization Algorithm
J. Offshore Mech. Arct. Eng (August 2025)
Effects of Aerodynamic Damping and Gyroscopic Moments on Dynamic Responses of a Semi-Submersible Floating Vertical Axis Wind Turbine: An Experimental Study
J. Offshore Mech. Arct. Eng (April 2025)
Investigating the Impact of System Parameters on Flow-Induced Vibration Hard Galloping Based on Deep Neural Network
J. Offshore Mech. Arct. Eng (August 2025)
Related Articles
Effect of Different Arc Welding Processes on the Metallurgical and Mechanical Properties of Ramor 500 Armor Steel
J. Eng. Mater. Technol (April,2020)
Effect of Charpy V Notch Position on Impact Toughness of all Weld Metal Welds and its Relevance With ASME Codes
J. Pressure Vessel Technol (August,2006)
A Predictive Electrochemical Model for Weld Metal Hydrogen Pickup in Underwater Wet Welds
J. Offshore Mech. Arct. Eng (November,1998)
Heat-Affected Zone Fracture Toughness of 420–500-MPa Yield Strength Steels: Effects of Chemical Composition and Welding Conditions
J. Offshore Mech. Arct. Eng (February,1993)
Related Chapters
Subsection NE—Class MC Components
Companion Guide to the ASME Boiler & Pressure Vessel Codes, Volume 1 Sixth Edition
Subsection NE — Class MC Components
Companion Guide to the ASME Boiler and Pressure Vessel Code, Volume 1, Third Edition
Subsection NE—Class MC Components
Companion Guide to the ASME Boiler & Pressure Vessel Code, Volume 1, Second Edition