This paper discusses results from a series of trials carried out to determine the effect of the projectile driving band on the stress applied to a gun barrel during firing. The interference between the driving band and gun barrel can apply significant loads to the barrel and, in extreme cases, lead to premature cracking and failure of the barrel. Strain gage data from firing trials has been used to characterize the external strain from firing different projectiles and charges to identify potential problems and provide information for fatigue analysis. Very high band strains were routinely measured under “oiled bore” conditions, i.e., after barrel cleaning and also during the first one to three rounds of a serial following a long pause in firing, such as at the start of a day’s firing. In general, the strain associated with the driving band was seen to decrease with increased charge zone, barrel wear, and, at higher charge zones, distance along the barrel. In the majority of tests fired at maximum charge, there was no strain peak associated with the driving band in the forward part of the barrel. In conjunction with these experimental observations, a laboratory study has been carried out on the effect of a narrow pressure band on the deformation of a thick-walled tube. An apparatus was constructed in order to pressurize a known length of a smooth-bore cylinder. Sealing width at the edges of the band was minimized to reduce edge effects, and an oversize pressurized “cap” was used to ensure that the bandwidth remained constant during the experiments. Spacer disks were used to vary the bandwidth and also to adjust the cylinder position relative to the band. Measured external strains on the tubes were compared to calculations based on analytical solutions for step pressure changes and are shown to be in good agreement.
Skip Nav Destination
e-mail: tdandrews@qinetiq.com
Article navigation
Research Papers
Projectile Driving Band Interactions With Gun Barrels
Tony D. Andrews
e-mail: tdandrews@qinetiq.com
Tony D. Andrews
QinetiQ
, Cody Technology Park, Ively Road, Farnborough, Hampshire GU14 0LX, United Kingdom
Search for other works by this author on:
Tony D. Andrews
QinetiQ
, Cody Technology Park, Ively Road, Farnborough, Hampshire GU14 0LX, United Kingdome-mail: tdandrews@qinetiq.com
J. Pressure Vessel Technol. May 2006, 128(2): 273-278 (6 pages)
Published Online: January 3, 2006
Article history
Received:
December 7, 2005
Revised:
January 3, 2006
Citation
Andrews, T. D. (January 3, 2006). "Projectile Driving Band Interactions With Gun Barrels." ASME. J. Pressure Vessel Technol. May 2006; 128(2): 273–278. https://doi.org/10.1115/1.2172965
Download citation file:
Get Email Alerts
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of a Cannon
J. Pressure Vessel Technol (December 2024)
Dynamic Response and Damage Analysis of a Large Steel Tank Impacted by an Explosive Fragment
J. Pressure Vessel Technol (February 2025)
Related Articles
Mechanism of Interior Ballistic Peak Phenomenon of Guns and Its Effects
J. Appl. Mech (September,2010)
Dynamical Loading of the Muzzle Area of a Gun Barrel Including a Muzzle Brake
J. Pressure Vessel Technol (May,2006)
Influence of Rotating Band Construction on Gun Tube Loading—Part II: Measurement and Analysis
J. Pressure Vessel Technol (August,2012)
Reduction of Heat Transfer to Gun Barrels by Wear-Reducing Additives
J. Heat Transfer (November,1975)
Related Proceedings Papers
Related Chapters
Cavitation Induction by Projectile Impacting on a Water Jet
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Optimal Shape Design Approach and Influence on the Projectile Vertices with Respect to Some Objective Function
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Understanding the Problem
Design and Application of the Worm Gear