Numerical simulation of fatigue crack propagation based on fracture mechanics and the conventional finite element method requires a huge amount of computational resources when the cracked structure shows a complicated condition such as the multiple site damage or thermal fatigue. The objective of the present study is to develop a simulation technique for fatigue crack propagation that can be applied to complex situations by employing the continuum damage mechanics (CDM). An anisotropic damage tensor is defined to model a macroscopic fatigue crack. The validity of the present theory is examined by comparing the elastic stress distributions around the crack tip with those obtained by a conventional method. Combined with a nonlinear elasto-plastic constitutive equation, numerical simulations are conducted for low cycle fatigue crack propagation in a plate with one or two cracks. The results show good agreement with the experiments. Finally, propagations of multiply distributed cracks under low cycle fatigue loading are simulated to demonstrate the potential application of the present method.
Skip Nav Destination
e-mail: mtak@iis.u-tokyo.ac.jp
e-mail: nakamt@chofu.jaxa.jp
Article navigation
February 2007
Research Papers
Fatigue Crack Modeling and Simulation Based on Continuum Damage Mechanics
Masakazu Takagaki,
Masakazu Takagaki
Institute of Industrial Science,
e-mail: mtak@iis.u-tokyo.ac.jp
The University of Tokyo
, 4-6-1 Komaba, Meguro, Tokyo, 153-8505 Japan
Search for other works by this author on:
Toshiya Nakamura
Toshiya Nakamura
Aviation Program Group,
e-mail: nakamt@chofu.jaxa.jp
Japan Aerospace Exploration Agency
, 6-13-1 Osawa, Mitaka, Tokyo, 181-0015 Japan
Search for other works by this author on:
Masakazu Takagaki
Institute of Industrial Science,
The University of Tokyo
, 4-6-1 Komaba, Meguro, Tokyo, 153-8505 Japane-mail: mtak@iis.u-tokyo.ac.jp
Toshiya Nakamura
Aviation Program Group,
Japan Aerospace Exploration Agency
, 6-13-1 Osawa, Mitaka, Tokyo, 181-0015 Japane-mail: nakamt@chofu.jaxa.jp
J. Pressure Vessel Technol. Feb 2007, 129(1): 96-102 (7 pages)
Published Online: March 10, 2006
Article history
Received:
April 20, 2005
Revised:
March 10, 2006
Citation
Takagaki, M., and Nakamura, T. (March 10, 2006). "Fatigue Crack Modeling and Simulation Based on Continuum Damage Mechanics." ASME. J. Pressure Vessel Technol. February 2007; 129(1): 96–102. https://doi.org/10.1115/1.2388993
Download citation file:
Get Email Alerts
Cited By
Measurement of Steam-Generator-Tube Vibration Damping Caused by Anti-Vibration-Bar Supports
J. Pressure Vessel Technol (February 2025)
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of a Cannon
J. Pressure Vessel Technol (December 2024)
Dynamic Response and Damage Analysis of a Large Steel Tank Impacted by an Explosive Fragment
J. Pressure Vessel Technol (February 2025)
Related Articles
Transition of Crack Propagation Path Under Varied Levels of Load in Bimodal Grain Size Al-Mg Alloy
J. Eng. Mater. Technol (October,2011)
Finite Element Modeling of Fatigue Damage Using a Continuum Damage Mechanics Approach
J. Pressure Vessel Technol (May,2005)
An Experimental Investigation of Bending Fatigue Initiation and Propagation Lives
J. Mech. Des (September,2001)
Fatigue Life Prediction Modeling for Turbine Hot Section Materials
J. Eng. Gas Turbines Power (April,1989)
Related Proceedings Papers
Related Chapters
Introductory Information
The Stress Analysis of Cracks Handbook, Third Edition
A New Formula on Fatigue Crack Propagation
International Conference on Mechanical and Electrical Technology 2009 (ICMET 2009)
Fatigue Crack Growth, Fatigue, and Stress Corrosion Crack Growth: Section XI Evaluation
Online Companion Guide to the ASME Boiler & Pressure Vessel Codes