A computational model is established to simulate the combustion and thermal-flow behavior inside a petcoke rotary calcining kiln. The results show that peak temperature is located at the tertiary air zone and a cold region that exists between the natural gas combustion zone and the tertiary air zone causes the coke bed to lose heat to the gas stream. The cold tertiary air injections reduce the gas temperature inside the kiln, so preheating the tertiary air using extracted gas or other waste energy is essential to saving energy. The devolatilization rate and location have a pronounced effect on the simulated temperature distribution. As the calcining kiln rotates, the tertiary air injection nozzles will move relative to the coke bed and exert cyclic air-bed interactions. At zero angular position, the air injection nozzles are diametrically located away from the bed so the interactions between the tertiary air jets and the coke bed are minimal. As the kiln rotates to a 180 deg position, the stem of the air injection nozzles are actually buried inside the coke bed with the nozzles protruding outward from the bed. At this position, the tertiary air jets will provide a fresh layer of air just above the coke bed, and the interaction between the air flow and the coke bed becomes strong. The 45 deg rotational angle case shows a better calcination with a 100 K higher bed surface temperature at the discharge end compared with the rest of rotational angles. Without including the coke fines combustion and the coke bed, the lumped gas temperature for the rotational cases shows a peak temperature of 1400 K at , which is due to natural gas combustion; the lowest temperature is around 1075 K at two locations, and 8. The exhaust gas temperature is approximately 1100 K. The insight gained from this study will be used to design innovative means to reduce natural gas consumption.
Skip Nav Destination
e-mail: zzhang@uno.edu
e-mail: twang@uno.edu
Article navigation
June 2010
Research Papers
Simulation of Combustion and Thermal-Flow Inside a Petroleum Coke Rotary Calcining Kiln—Part II: Analysis of Effects of Tertiary Airflow and Rotation
Zexuan Zhang,
Zexuan Zhang
Research Assistant
Energy Conversion and Conservation Center,
e-mail: zzhang@uno.edu
University of New Orleans
, New Orleans, LA 70148-2220
Search for other works by this author on:
Ting Wang
Ting Wang
Professor
Energy Conversion and Conservation Center,
e-mail: twang@uno.edu
University of New Orleans
, New Orleans, LA 70148-2220
Search for other works by this author on:
Zexuan Zhang
Research Assistant
Energy Conversion and Conservation Center,
University of New Orleans
, New Orleans, LA 70148-2220e-mail: zzhang@uno.edu
Ting Wang
Professor
Energy Conversion and Conservation Center,
University of New Orleans
, New Orleans, LA 70148-2220e-mail: twang@uno.edu
J. Thermal Sci. Eng. Appl. Jun 2010, 2(2): 021007 (7 pages)
Published Online: October 28, 2010
Article history
Received:
February 6, 2010
Revised:
September 9, 2010
Online:
October 28, 2010
Published:
October 28, 2010
Connected Content
A companion article has been published:
Simulation of Combustion and Thermal-Flow Inside a Petroleum Coke Rotary Calcining Kiln—Part I: Process Review and Modeling
Citation
Zhang, Z., and Wang, T. (October 28, 2010). "Simulation of Combustion and Thermal-Flow Inside a Petroleum Coke Rotary Calcining Kiln—Part II: Analysis of Effects of Tertiary Airflow and Rotation." ASME. J. Thermal Sci. Eng. Appl. June 2010; 2(2): 021007. https://doi.org/10.1115/1.4002525
Download citation file:
Get Email Alerts
Cited By
Simulation and Experimental Study of Two-Phase Gas–Liquid Behavior in Two-Dimensional Porous Medium Based on Lattice Boltzmann Method
J. Thermal Sci. Eng. Appl (February 2025)
Effect of Variation of the Aspect Ratio of Rectangular Twisted Tapes Inserted in a Circular Pipe on the Thermal Performance
J. Thermal Sci. Eng. Appl (February 2025)
Design Optimization of a Shell-and-Tube Heat Exchanger Based on Variable Baffle Cuts and Sizing
J. Thermal Sci. Eng. Appl (February 2025)
Energy-Efficient Three-Wheel Bleedless Electrical Environmental Control System for a Passenger Aircraft
J. Thermal Sci. Eng. Appl (February 2025)
Related Articles
Simulation of Combustion and Thermal-Flow Inside a Petroleum Coke Rotary Calcining Kiln—Part I: Process Review and Modeling
J. Thermal Sci. Eng. Appl (June,2010)
Simulation of Char Dust Combustion Inside a Pyroscrubber Downstream of a Petroleum Coke Calcining Kiln
J. Thermal Sci. Eng. Appl (March,2012)
Investigation of Potential Benefits of Using Bricks of High Thermal Capacity and Conductivity in a Rotating Calcining Kiln
J. Thermal Sci. Eng. Appl (March,2009)
Investigation of Combustion and Thermal-Flow Inside a Petroleum Coke Rotary Calcining Kiln With Potential Energy Saving Considerations
J. Thermal Sci. Eng. Appl (March,2013)
Related Proceedings Papers
Related Chapters
Combined Cycle Power Plant
Energy and Power Generation Handbook: Established and Emerging Technologies
A Simple Carburetor
Case Studies in Fluid Mechanics with Sensitivities to Governing Variables
Gas-Fluidized Beds
Two-Phase Heat Transfer