The laminar squeeze flow of a viscous incompressible fluid between a flat circular disk and an axisymmetric curved disk of arbitrary shape is investigated theoretically using modified lubrication theory. The characteristics of squeeze film are investigated through inertia and curvature effects on the normal force exerted on the upper curved moving disk described by an exponential function for the sinusoidal squeeze motion. The constant force squeezing state is also examined. It has been observed that the load carrying capacity of the curved squeeze film is strongly influenced by the curvature and inertia effects.
Issue Section:
Technical Notes
Keywords:
film flow,
confined flow,
laminar flow,
nonequilibrium flow,
flow simulation,
viscosity,
force,
lubrication
1.
Borgin
, P.
, and Tichy
, J. A.
, 1985
, “Lubricating Films of a Viscoelastic Fluid, Including Fluid Inertia, Studied by a Linearization Method
,” Int. J. Eng. Sci.
, 23
, pp. 1135
–1149
.2.
Hashimoto
, H.
, and Wada
, S.
, 1986
, “The Effects of Fluid Inertia Forces in Parallel Circular Squeeze Film Bearings Lubricated With Pseudoplastic Fluids
,” ASME J. Tribol.
, 108
, pp. 282
–287
.3.
Esmonde
, H.
, Fitzpatrick
, J. A.
, Rice
, H. J.
, and Axisa
, F.
, 1992
, “Modelling and Identification of Nonlinear Squeeze Film Dynamics
,” J. Fluids Struct.
6
, pp. 223
–248
.4.
Bhat
, M. V.
, and Deheri
, G. M.
, 1993
, “Magnetic-Fluid-Based Squeeze Film in Curved Porous Circular Discs
,” J. Magn. Magn. Mater.
, 127
, pp. 159
–162
.5.
Hashimoto
, H.
, 1994
, “Viscoelastic Squeeze Film Characteristics with Inertia Effects Between Two Parallel Circular Plates Under Sinusoidal Motion
,” ASME J. Tribol.
, 116
, pp. 161
–166
.6.
Hashimoto
, H.
, 1995
, “Squeeze Film Characteristics between Parallel Circular Plates Containing a Single Central Air Bubble in the Internal Flow Regime
,” ASME J. Tribol.
, 117
, pp. 513
–518
.7.
Tichy
, J. A.
, 1995
, “A Porous Media Model for Thin Film Lubrication
,” ASME J. Tribol.
, 117
, pp. 16
–21
.8.
Han
, Y.
, and Rogers
, R. J.
, 1996
, “Squeeze Film Force Modeling for Large Amplitude Motion Using an Elliptical Velocity Profile
,” ASME J. Tribol.
, 118
, pp. 687
–692
.9.
Usha
, R.
, and Rukmani
, R.
, 1998
, “An Investigation of a Squeeze Film Between Two Plane Annuli
,” ASME J. Tribol.
, 120
, pp. 610
–615
.10.
Laun
, H. M.
, Rady
, M.
, and Hassager
, O.
, 1999
, “Analytical Solutions for Squeeze Flow with Partial Wall Slip
,” J. Non-Newtonian Fluid Mech.
, 81
, pp. 1
–15
.11.
Shah
, R. C.
, and Bhat
, M. V.
, 2000
, “Squeeze Film Based on Magnetic Fluid in Curved Porous Rotating Circular Plate
,” J. Magn. Magn. Mater.
, 208
, pp. 115
–119
.12.
San Andres
, L. A.
, and Vance
, J. M.
, 1986
, “Effects of Fluid Inertia and Turbulence on the Force Coefficients for Squeeze Film Dampers
,” ASME J. Eng. Gas Turbines Power
, 108
, pp. 332
–339
.13.
Hays
, D. F.
, 1963
, “Squeeze Films for Rectangle Plates
,” ASME J. Basic Eng.
, 85
, pp. 243
–246
.14.
Murti
, P. R. K.
, 1975
, “Squeeze Films in Curved Circular Plates
,” ASME J. Lubr. Technol.
, 97
, pp. 650
–652
.15.
Gupta
, J. L.
, and Vora
, K. H.
, 1980
, “Analysis of Squeeze Films Between Curved Annular Plates
,” ASME J. Lubr. Technol.
, 102
, pp. 48
–50
.16.
Gupta
, R. S.
, and Kapur
, V. K.
, 1980
, “The Simultaneous Effects of Thermal and Inertia in Curved Circular Squeeze Films
,” ASME J. Lubr. Technol.
, 102
, pp. 501
–504
.17.
Vora
, K. H.
, and Bhat
, M. V.
, 1980
, “The Load Capacity of a Squeeze Film Between Curved Porous Roating Circular Plates
,” Wear
, 65
, pp. 39
–46
.18.
Hasegawa
, E.
, 1985
, “On Squeeze Film of a Curved Circular Plate
,” Bull. JSME
, 28
, pp. 951
–958
.19.
Hasegawa
, E.
, Kanda
, T.
, and Watanabe
, H.
, 1986
, “Squeeze Films Between a Rotating Curved Disk and a Plane Wall
,” Bull. JSME
, 29
, pp. 1919
–1926
.20.
Crandall
, S. H.
, and El-Shafei
, A.
, 1993
, “Momentum and Energy Approximations for Elementary Squeeze Film Damper Flows
,” ASME J. Appl. Mech.
, 60
, pp. 728
–735
.21.
Ishizawa
, S.
, 1966
, “The Unsteady Laminar Flow Between Two Parallel Discs With Arbitrarily Varying Gap Width
,” Bull. JSME
, 9
, pp. 533
–550
.Copyright © 2002
by ASME
You do not currently have access to this content.