The characterization of frictional phenomena at the tool-chip-workpiece interface in metal cutting remains a challenge. This paper aims at identifying a friction model and a heat partition model at this interface during the dry cutting of an AISI1045 steel with TiN coated carbide tools. A new tribometer, based on a modified pin-on-ring system, has been used in order to reach relevant values of pressures, temperatures, and sliding velocities. Additionally a 3D Arbitrary Lagrangian Eulerian model (A.L.E.) numerical model simulating the frictional test has been developed in order to extract local parameters around the spherical pin, such as average contact pressure, average local sliding velocity, and average contact temperature, from experimental macroscopic measurements. A large range of sliding velocities [0.083–5 m/s] has been investigated. It has been shown that friction coefficient and heat partition coefficient are mainly dependant on local sliding velocity at the interface. Three friction regimes have been identified. These experimental and numerical results provide a better understanding of the tribological phenomena along the tool-chip-workpiece interfaces in dry machining of an AISI 1045 steel with a TiN coated carbide tool. Finally a new friction model and heat partition model has been developed for implementation in a numerical cutting model.
Skip Nav Destination
e-mail: abdel.dogui@enim.rnu.tn
Article navigation
October 2011
Research Papers
Identification of a Friction Model at the Tool-Chip-Workpiece Interface in Dry Machining of a AISI 1045 Steel With a TiN Coated Carbide Tool
Hamdi Ben Abdelali,
Hamdi Ben Abdelali
Laboratoire de Génie Mécanique,
Université de Monastir
, Ecole Nationale d’Ingénieurs de Monastir, Avenue Ibn Al-Jazzar, 5019 Monastir, Tunisie
e-mail:
Search for other works by this author on:
Cedric Courbon,
Cedric Courbon
Université de Lyon
, Ecole Centrale de Lyon, LTDS, UMR CNRS 5513, 36 Avenue Guy de Collongue, 69134 Ecully, France
e-mail:
Search for other works by this author on:
Joël Rech,
Joël Rech
Université de Lyon
, ENISE, LTDS, UMR CNRS 5513, 58 Rue Jean Parot, 42023 Saint-Etienne, France
e-mail:
Search for other works by this author on:
Abdelwaheb Dogui,
Abdelwaheb Dogui
Laboratoire de Génie Mécanique,
e-mail: abdel.dogui@enim.rnu.tn
Université de Monastir
, Ecole Nationale d’Ingénieurs de Monastir, Avenue Ibn Al-Jazzar, 5019 Monastir, Tunisie
Search for other works by this author on:
Philippe Kapsa
Philippe Kapsa
LTDS, UMR CNRS 5513,
Université de Lyon
, Ecole Centrale de Lyon, 36 Avenue Guy de Collongue, 69134 Ecully, France
e-mail:
Search for other works by this author on:
Hamdi Ben Abdelali
Laboratoire de Génie Mécanique,
Université de Monastir
, Ecole Nationale d’Ingénieurs de Monastir, Avenue Ibn Al-Jazzar, 5019 Monastir, Tunisie
e-mail:
Cedric Courbon
Université de Lyon
, Ecole Centrale de Lyon, LTDS, UMR CNRS 5513, 36 Avenue Guy de Collongue, 69134 Ecully, France
e-mail:
Joël Rech
Université de Lyon
, ENISE, LTDS, UMR CNRS 5513, 58 Rue Jean Parot, 42023 Saint-Etienne, France
e-mail:
Abdelwaheb Dogui
Laboratoire de Génie Mécanique,
Université de Monastir
, Ecole Nationale d’Ingénieurs de Monastir, Avenue Ibn Al-Jazzar, 5019 Monastir, Tunisie
e-mail: abdel.dogui@enim.rnu.tn
Philippe Kapsa
LTDS, UMR CNRS 5513,
Université de Lyon
, Ecole Centrale de Lyon, 36 Avenue Guy de Collongue, 69134 Ecully, France
e-mail: J. Tribol. Oct 2011, 133(4): 042201 (11 pages)
Published Online: October 6, 2011
Article history
Received:
December 25, 2010
Revised:
August 1, 2011
Online:
October 6, 2011
Published:
October 6, 2011
Citation
Abdelali, H. B., Courbon, C., Rech, J., Ben Salem, W., Dogui, A., and Kapsa, P. (October 6, 2011). "Identification of a Friction Model at the Tool-Chip-Workpiece Interface in Dry Machining of a AISI 1045 Steel With a TiN Coated Carbide Tool." ASME. J. Tribol. October 2011; 133(4): 042201. https://doi.org/10.1115/1.4004879
Download citation file:
Get Email Alerts
Static Characteristics of Hybrid Water-Lubricated Herringbone Groove Journal Bearing
J. Tribol (April 2025)
Related Articles
3D FEA Modeling of Hard Turning
J. Manuf. Sci. Eng (May,2002)
The Effect of Workpiece Hardness and Cutting Speed on the Machinability of AISI H13 Hot Work Die Steel When Using PCBN Tooling
J. Manuf. Sci. Eng (August,2002)
Predictive Models for Flank Wear on Coated Inserts
J. Tribol (January,2000)
Mechanics of Machining With Chamfered Tools
J. Manuf. Sci. Eng (November,2000)
Related Proceedings Papers
Related Chapters
GA Based Multi Objective Optimization of the Predicted Models of Cutting Temperature, Chip Reduction Co-Efficient and Surface Roughness in Turning AISI 4320 Steel by Uncoated Carbide Insert under HPC Condition
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Cutting and Machining
Fabrication of Metallic Pressure Vessels
Modeling of Cutting Force in Vibration-Assisted Machining
Vibration Assisted Machining: Theory, Modelling and Applications