Abstract

Geared turbofans need to withstand loss of lubrication due to inevitable off-design conditions. Additionally, the loss of lubrication specifications that have to be fulfilled are getting stricter. For a loss of lubrication event, today's geared turbofans are equipped with secondary oil supply systems. Their omission would reduce space and weight and, consequently, carbon emissions. However, this requires geared transmissions to withstand loss of lubrication events. In order to enable this, knowledge of the power loss and damage behavior of gears under loss of lubrication is required first. In this study, power loss and bulk temperature measurements of test gears under loss of lubrication on an FZG gear efficiency test rig are presented. Hertzian pressures in the pitch point up to 1723 N/mm2 and circumferential speeds up to 20 m/s were considered. The experimental results show the characteristics of increasing power loss and bulk temperatures under loss of lubrication depending on load and speed. At moderate operating conditions, no damage occurs within 20 s under loss of lubrication, whereas a load increase results in slight scuffing, and a speed increase results in severe scuffing. Oil centrifugation has a strong effect on the loss of lubrication performance. Additional experiments under reduced quantity lubrication demonstrate the impact of the remaining oil on the survivability of gears facing the loss of lubrication.

Graphical Abstract Figure
Graphical Abstract Figure
Close modal

References

1.
von Plehwe
,
F. C.
,
Schwitzke
,
C.
, and
Bauer
,
H.-J.
,
2021
, “
Heat Transfer Coefficient Distribution on Oil Injection Cooled Gears: Experimental Method, Uncertainty, and Results
,”
ASME J. Tribol.
,
143
(
9
), p.
091201
.
2.
European Union Aviation Safety Agency
,
2019
, “
Certification Specifications and Acceptable Means of Compliance for Large Rotorcraft CS-29—Amendment 7
,” European Union.
3.
Venner
,
C. H.
,
Popovici
,
G.
,
Lugt
,
P. M.
, and
Organisciak
,
M.
,
2008
, “
Film Thickness Modulations in Starved Elastohydrodynamically Lubricated Contacts Induced by Time-Varying Lubricant Supply
,”
ASME J. Tribol.
,
130
(
4
), p.
041501
.
4.
Li
,
S.
,
Kolivand
,
A.
, and
Anisetti
,
A.
,
2022
, “
An Investigation on Starvation Onset of Rough Surface Line Contacts
,”
ASME J. Tribol.
,
144
(
3
), p.
031602
.
5.
Federal Aviation Administration
,
1964
, “
Part 29—Airworthiness Standards: Transport Category Rotorcraft
,” Code of Federal Regulations.
6.
United States Army Aviation Troop Command and Aviation Research and Development Center
,
1996
, “
Aeronautical Design Standard—Rotorcraft Propulsion Performance and Qualification Requirements and Guidelines
,” Directorate for Engineering.
7.
Federal Aviation Administration
,
2007
, “
Extended Operations (ETOPS) of Multi-Engine Airplanes
,” Federal Register, 72 FR 1808, pp.
1808
1887
.
8.
Isaacson
,
A. C.
, and
Wagner
,
M. E.
,
2018
, “
Oil-off Characterization Method Using in-Situ Friction Measurement for Gears Operating Under Loss-of-Lubrication Conditions
,”
American Gear Manufacturers Association Fall Technical Meeting 2018
,
Oak Brook, IL
,
Sept. 24–26
, AGMA 18FTM08.
9.
Gasparini
,
G.
,
Motta
,
N.
,
Gabrielli
,
A.
, and
Colombo
,
D.
,
2014
, “
Gearbox Loss of Lubrication Performance: Myth, Art or Science?
,”
40th European Rotorcraft Forum 2014
,
Southampton, UK
,
Sept. 2–5
, pp.
1162
1175
.
10.
Sheridan
,
W. G.
,
2010
, “
Rotor Brake and Windmilling Lubrication System for Geared Turbofan Engine
,” U.S. Patent No. US 7,849,668 B2.
11.
Sheridan
,
W. G.
,
Portlock
,
L. E.
, and
McCune
,
M. E.
,
2011
, “
Lubrication System With Extended Emergency Operability
,” U.S. Patent No. US 8,020,665 B2.
12.
Sheridan
,
W. G.
,
2020
, “
Windmill and Negative-g Oil System for Geared Turbofan Engines
,” U.S. Patent No. US 10,578,017 B2.
13.
Chavez
,
A.
,
Baker
,
T.
, and
Fetty
,
J.
,
2017
, “
Future Advanced Rotorcraft Drive System (FARDS) Full Scale Gearbox Demonstration
,”
Annual Forum Proceedings—AHS International, 73rd American Helicopter Society International Annual Forum and Technology Display 2017
,
Fort Worth, TX
,
May 9–11
, pp.
2325
2335
.
14.
Kozachyn
,
M.
,
McIntyre
,
S.
,
Robuck
,
M.
,
Isaacson
,
A.
,
Black
,
B.
, and
Sahay
,
V.
,
2018
, “
Loss of Lubrication Testing
,”
Annual Forum Proceedings—AHS International
,
Phoenix, AZ
,
May 14–17
, Vol. 2018.
15.
Handschuh
,
R. F.
, and
Gargano
,
L. J.
,
2014
, “
Test Facility Simulation Results for Loss-of-Lubrication of Spur Gears
,” National Aeronautics and Space Administration, NASA/TM—2014-218396.
16.
Handschuh
,
R. F.
,
2015
, “
Thermal Behavior of Aerospace Spur Gears in Normal and Loss-of-Lubrication Conditions
,”
Annual Forum Proceedings—AHS International
,
Virginia Beach, CA
,
May 4–7
, 4(Issue January), pp.
2292
2301
.
17.
Bartilotta
,
I.
,
Ciulli
,
E.
,
Manconi
,
S.
, and
Toson
,
E.
,
2012
, “
An Experimental Investigation on Aerospace Quality Gears Operating in Loss of Lubrication Condition
,”
ASME Proceedings of the ASME 2012 11th Biennial Conference on Engineering Systems Design and Analysis. Volume 4: Advanced Manufacturing Processes; Biomedical Engineering; Multiscale Mechanics of Biological Tissues; Sciences, Engineering and Education; Multiphysics; Emerging Technologies for Inspection and Reverse Engineering; Advanced Materials and Tribology
,
Nantes, France
,
July 2–4
, pp.
621
627
.
18.
Zhang
,
H.
,
Sun
,
F.
,
Wu
,
H.
,
Chaudhry
,
Z.
, and
Maglieri
,
J.
,
2018
, “
Temperature Rise and Tooth Surface Evolution of Gearbox Under Loss of Lubrication: Experimental and Numerical Investigation
,”
Annual Forum Proceedings—AHS International
,
Phoenix, AZ
,
May 14–17
, Vol. 2018.
19.
Isaacson
,
A. C.
,
Wagner
,
M. E.
,
Rao
,
S. B.
, and
Sroka
,
G.
,
2016
, “
Impact of Surface Condition and Lubricant on Effective Gear Tooth Friction Coefficient
,”
AGMA 2016—Fall Technical Meeting
,
Pittsburgh, PA
,
Oct. 2–4
, pp. 41–47, AGMA 16FTM14.
20.
Navet
,
P.
,
Changenet
,
C.
,
Ville
,
F.
,
Ghribi
,
D.
, and
Cavoret
,
J.
,
2020
, “
Thermal Modeling of the FZG Test Rig: Application to Starved Lubrication Conditions
,”
Tribol. Trans.
,
63
(
6
), pp.
1135
1146
.
21.
Radil
,
K.
, and
Berkebile
,
S.
,
2020
, “
Failure Progression of Spur Gears During a Simulated Loss-of-Lubrication Event in a Rotorcraft Drive System
,”
Tribol. Trans.
,
63
(
4
), pp.
718
725
.
22.
Lechner
,
G.
,
1966
, “
Die Fress-Grenzlast bei Stirnrädern aus Stahl- Engl.: The Limit Scuffing Load for Spur Gears Made of Steel
,”
Ph.D. dissertation
,
Technical University of Munich
,
Munich
.
23.
Michaelis
,
K.
,
1987
, “
Die Integraltemperatur zur Beurteilung der Fresstragfähigkeit von Stirnradgetrieben- Engl.: The Integral Temperature for Assessment of the Scuffing Load Capacity of Spur Gears
,”
Ph.D. dissertation
,
Technical University of Munich
,
Munich
.
24.
Riggs
,
M. R.
,
Murthy
,
N. K.
, and
Berkebile
,
S. P.
,
2016
, “
Evaluation for Loss of Lubrication Performance of Black Oxide, Superfinished, and As-Ground Surfaces for Use in Rotorcraft Transmissions
,” Defense Technical Information Center.
25.
Riggs
,
M. R.
,
Murthy
,
N. K.
, and
Berkebile
,
S. P.
,
2017
, “
Scuffing Resistance and Starved Lubrication Behavior in Helicopter Gear Contacts: Dependence on Material, Surface Finish, and Novel Lubricants
,”
Tribol. Trans.
,
60
(
5
), pp.
932
941
.
26.
Alberti
,
J.
, and
Lemanski
,
A.
,
1972
, “
Oil-Starvation Test Program: Evaluation of VASCO-X2 Steel Spiral Bevel Gears
,” U.S. Army Air Mobility Research and Development Laboratory, Technical Report 72-19.
27.
Lohner
,
T.
,
2016
, “
Berechnung von TEHD Kontakten und Einlaufverhalten von Verzahnungen- Engl.: Calculation of TEHL Contacts and Running-in Behavior of Gears
,”
Ph.D. dissertation
,
Technical University of Munich
,
Munich
.
28.
Hinterstoißer
,
M.
,
Sedlmair
,
M.
,
Lohner
,
T.
, and
Stahl
,
K.
,
2019
, “
Minimizing Load-Dependent Gear Losses
,”
Tribol. Lubr. Technol.
,
66
(
3
), pp.
15
25
.
29.
Doleschel
,
A.
,
2002
, “
Method to Determine the Frictional Behaviour of Lubricants Using a FZG Gear Test Rig—FVA Information Sheet 345
,” Forschungsvereinigung Antriebstechnik e.V.
30.
Laukotka
,
E. M.
,
2007
, “
Heft 660—FVA Referenzölkatalog (Reference Lubricants Data Collection)
,” Forschungsvereinigung Antriebstechnik e.V.
31.
International Organization for Standardization
,
2004
, “
Gears—FZG Test Procedures-Part 2: FZG Step Load Test A10/16, 6R/120 for Relative Scuffing Load-Carrying Capacity of High EP Oils
,” ISO 14635-2:2004.
32.
Shell
,
2021
, “
Technical Data Sheet—AeroShell Turbine Oil 500: Synthetic Lubricating Oil for Aircraft Turbine Engines
,” Shell plc.
33.
Shell
,
2022
, “
Safety Data Sheet—AeroShell Turbine Oil 500: Synthetic Lubricating Oil for Aircraft Turbine Engines
,” Shell plc.
34.
Naval Air Warfare Center Aircraft Division
,
2019
, “
MIL-PRF-23699. Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Numbers: O-152, O-154, O-156, and O-167
,” Military and Government Specs & Standards.
35.
International Organization for Standardization
,
2000
, “
Gears—FZG Test Procedures-Part 1: FZG Test Method A/8,3/90 for Relative Scuffing Load-Carrying Capacity of Oils
,” ISO 14635-1:2000.
36.
Faruck
,
A. A. M.
,
Hsu
,
C.-J.
,
Doerr
,
N.
,
Weigand
,
M.
, and
Gachot
,
C.
,
2020
, “
How Lubricant Formulations and Properties Influence the Performance of Rotorcraft Transmissions Under Loss of Lubrication Conditions
,”
Tribol. Int.
,
151
, p.
106390
.
37.
Keller
,
M. C.
,
Braun
,
S.
,
Wieth
,
L.
,
Chaussonnet
,
G.
,
Dauch
,
T. F.
,
Koch
,
R.
,
Schwitzke
,
C.
, and
Bauer
,
H.-J.
,
2019
, “
Smoothed Particle Hydrodynamics Simulation of Oil-Jet Gear Interaction
,”
ASME J. Tribol.
,
141
(
7
), p.
071703
.
38.
Ishibashi
,
A.
, and
Tanaka
,
S.
,
1981
, “
Effects of Hunting Gear Ratio Upon Surface Durability of Gear Teeth
.”
ASME J. Mech. Des.
,
103
(
1
), pp.
227
235
.
You do not currently have access to this content.