Graphical Abstract Figure
Abstract
This study explores the influence of cobalt content on the tribomechanical and corrosion properties of Ni–Co–P coatings deposited through reverse pulse electroplating. The ratio of Co salt concentration to the total Ni and Co salt concentration was varied in the electrolyte to achieve different Co levels within relatively low cobalt (≤36 wt%) regime. X-ray diffraction revealed crystallite sizes of 1–3 nm in the deposited layers suggesting a mixture of amorphous and nanocrystalline structure. Critical loads in scratch adhesion tests are found to be in between 10.5 N and 15.1 N implying adequate adhesive bonding between the deposits and the substrates. Microhardness and pin-on-disc tribo test results demonstrate a positive correlation between Co content and both hardness and wear resistance of the coatings. However, incorporating small amounts of Co (≤6.2 wt%) exhibited minimal impact on these properties. Interestingly, corrosion resistance in saline medium peaked at the second-highest Co level (26.2 wt% of Co), followed by a decrease with further increase of Co. These findings indicate an optimal Co concentration for achieving a balance between wear resistance and corrosion protection in Ni–Co–P coatings.
References
1.
Hsissou
, R.
, Azogagh
, M.
, Benhiba
, F.
, Echihi
, S.
, Galai
, M.
, Shaim
, A.
, Bahaj
, H.
, et al, 2022
, “Insight of Development of Two Cured Epoxy Polymer Composite Coatings as Highly Protective Efficiency for Carbon Steel in Sodium Chloride Solution: DFT, RDF, FFV and MD Approaches
,” J. Mol. Liq.
, 360
, p. 119406
. 2.
Sengupta
, S.
, Murmu
, M.
, Mandal
, S.
, Hirani
, H.
, and Banerjee
, P.
, 2021
, “Competitive Corrosion Inhibition Performance of Alkyl/Acyl Substituted 2-(2-Hydroxybenzylideneamino) Phenol Protecting Mild Steel Used in Adverse Acidic Medium: A Dual Approach Analysis Using FMOs/Molecular Dynamics Simulation Corroborated Experimental Findings
,” Colloids Surf. A
, 617
, p. 126314
. 3.
El-Mokadem
, T. H.
, Hashem
, A. I.
, Abd El-Sattar
, N. E.
, Dawood
, E. A.
, and Abdelshafi
, N. S.
, 2023
, “Green Synthesis, Electrochemical, DFT Studies and MD Simulation of Novel Synthesized Thiourea Derivatives on Carbon Steel Corrosion Inhibition in 1.0 M HCl
,” J. Mol. Struct.
, 1274
(2
), p. 134567
. 4.
Sahoo
, P.
, and Das
, S. K.
, 2011
, “Tribology of Electroless Nickel Coatings—a Review
,” Mater. Des.
, 32
(4
), pp. 1760
–1775
. 5.
Murdock
, E. S.
, Natarajan
, B. R.
, and Walmsley
, R. G.
, 1990
, “Noise Properties of Multilayered Co-Alloy Magnetic Recording Media
,” IEEE Trans. Magn.
, 26
(5
), pp. 2700
–2705
. 6.
Farr
, J. P. G.
, and Noshani
, A. A.
, 1996
, “Some Properties of Electroless Ni–P, Co–P, and Ni–Co–P Deposits
,” Trans. IMF
, 74
(6
), pp. 221
–225
. 7.
Parente
, M. M. V.
, Mattos
, O. R.
, Diaz
, S. L.
, Neto
, P. L.
, and Miranda
, F. F.
, 2001
, “Electrochemical Characterization of Ni–P and Ni–Co–P Amorphous Alloy Deposits Obtained by Electrodeposition
,” J. Appl. Electrochem.
, 31
(6
), pp. 677
–683
. 8.
Ma
, C.
, Wang
, S. C.
, Wang
, L. P.
, Walsh
, F. C.
, and Wood
, R. J. K.
, 2013
, “The Electrodeposition and Characterisation of Low-Friction and Wear-Resistant Co–Ni–P Coatings
,” Surf. Coat. Technol.
, 235
, pp. 495
–505
. 9.
Li
, N. J.
, Li
, M. M.
, and Li
, N. W.
, 2013
, “The Study on Preparation and Apply of Ni–Co–P Alloy Coating
,” Adv. Mater. Res.
, 690
, pp. 2145
–2148
. 10.
Mondal
, K.
, Sathithsuksanoh
, N.
, and Lalvani
, S. B.
, 2020
, “Electrodeposition and Characterization of NiCoP
,” SN Appl. Sci.
, 2
(12
), pp. 1
–12
. 11.
Gao
, Y.
, Huang
, L.
, Zheng
, Z. J.
, Li
, H.
, and Zhu
, M.
, 2007
, “The Influence of Cobalt on the Corrosion Resistance and Electromagnetic Shielding of Electroless Ni–Co–P Deposits on Al Substrate
,” Appl. Surf. Sci.
, 253
(24
), pp. 9470
–9475
. 12.
Theeratatpong
, K.
, Danchaivijit
, S.
, and Boonyongmaneerat
, Y.
, 2014
, “Effects of Co Content and Heat Treatment on Mechanical Properties of Electrolessly Deposited Ni–Co–P Alloys
,” Surf. Interface Anal.
, 46
(4
), pp. 276
–282
. 13.
Younan
, M. M.
, Aly
, I. H. M.
, and Nageeb
, M. T.
, 2002
, “Effect of Heat Treatment on Electroless Ternary Nickel–Cobalt–Phosphorus Alloy
,” J. Appl. Electrochem.
, 32
(4
), pp. 439
–446
. 14.
Jafari
, R.
, Ahmadi
, N. P.
, Khosroshahi
, R. A.
, and Raghebi
, Z.
, 2023
, “Depositing Ni–Co–P Alloy Coating on AISI316 Steel and Analyzing Its Properties
,” Surf. Rev. Lett.
, 30
(2
), p. 2350005
. 15.
Selvi
, V. E.
, Seenivasan
, H.
, and Rajam
, K. S.
, 2012
, “Electrochemical Corrosion Behavior of Pulse and DC Electrodeposited Co–P Coatings
,” Surf. Coat. Technol.
, 206
(8–9
), pp. 2199
–2206
. 16.
Chandrasekar
, M. S.
, and Pushpavanam
, M.
, 2008
, “Pulse and Pulse Reverse Plating—Conceptual, Advantages and Applications
,” Electrochim. Acta
, 53
(8
), pp. 3313
–3322
. 17.
Pellicer
, E.
, Gómez
, E.
, and Vallés
, E.
, 2006
, “Use of the Reverse Pulse Plating Method to Improve the Properties of Cobalt–Molybdenum Electrodeposits
,” Surf. Coat. Technol.
, 201
(6
), pp. 2351
–2357
. 18.
Ranjith
, B.
, and Paruthimal Kalaignan
, G.
, 2010
, “Ni–Co–TiO2 Nanocomposite Coating Prepared by Pulse and Pulse Reversal Methods Using Acetate Bath
,” Appl. Surf. Sci.
, 257
(1
), pp. 42
–47
. 19.
Karslioglu
, R.
, and Akbulut
, H.
, 2015
, “Comparison Microstructure and Sliding Wear Properties of Nickel–Cobalt/CNT Composite Coatings by DC, PC and PRC Current Electrodeposition
,” Appl. Surf. Sci.
, 353
, pp. 615
–627
. 20.
Bahrololoom
, M. E.
, and Sani
, R.
, 2005
, “The Influence of Pulse Plating Parameters on the Hardness and Wear Resistance of Nickel–Alumina Composite Coatings
,” Surf. Coat. Technol.
, 192
(2–3
), pp. 154
–163
. 21.
Zhang
, A.
, Xiao
, Y.
, Cao
, Y.
, Fang
, H.
, Zhang
, Y.
, Das
, P.
, and Zhang
, H.
, 2021
, “Electrodeposition, Formation Mechanism, and Electrocatalytic Performance of Co–Ni–P Ternary Catalysts Coated on Carbon Fiber Paper
,” J. Solid State Electrochem.
, 25
(5
), pp. 1503
–1512
. 22.
Zhang
, Y.
, Mbugua
, N. S.
, Jin
, H.
, and Chen
, L.
, 2023
, “Preparation and Investigation of Ni–Co–P Alloy Coatings Using Jet Electrodeposition With Varying Pulse Parameters
,” Crystals
, 13
(2
), p. 303
. 23.
Jović
, V. D.
, Jović
, B. M.
, and Pavlović
, M. G.
, 2006
, “Electrodeposition of Ni, Co and Ni–Co Alloy Powders
,” Electrochim. Acta
, 51
(25
), pp. 5468
–5477
. 24.
Kamel
, M. M.
, 2007
, “Anomalous Codeposition of Co–Ni: Alloys From Gluconate Baths
,” J. Appl. Electrochem.
, 37
(4
), pp. 483
–489
. 25.
Zamani
, M.
, Amadeh
, A.
, and Lari Baghal
, S. M.
, 2016
, “Effect of Co Content on Electrodeposition Mechanism and Mechanical Properties of Electrodeposited Ni–Co Alloy
,” Trans. Nonferrous Met. Soc. China
, 26
(2
), pp. 484
–491
. 26.
Bai
, A.
, and Hu
, C. C.
, 2002
, “Effects of Electroplating Variables on the Composition and Morphology of Nickel–Cobalt Deposits Plated Through Means of Cyclic Voltammetry
,” Electrochim. Acta
, 47
(21
), pp. 3447
–3456
. 27.
Chen
, K.
, Li
, Y.
, Wu
, G.
, Wang
, Q.
, Fan
, C.
, Zhang
, L.
, Song
, J.
, and Han
, S.
, 2023
, “Electrodeposited Ni−Co−P Triple-Layered Structure as a Robust and Durable Electrocatalyst for Hydrogen Evolution
,” J. Electrochem. Soc.
, 170
(9
), p. 096501
. 28.
Klug
, H. P.
, and Alexander
, L. E.
, 1974
, X-Ray Diffraction Procedures: For Polycrystalline and Amorphous Materials
, Wiley
, New York
.29.
de la Peña O′ Shea
, V. A.
, de la Piscina
, P. R.
, Homs
, N.
, Aromi
, G.
, and Fierro
, J. L.
, 2009
, “Development of Hexagonal Closed-Packed Cobalt Nanoparticles Stable at High Temperature
,” Chem. Mater.
, 21
(23
), pp. 5637
–5643
. 30.
Harrington
, G. F.
, and Santiso
, J.
, 2021
, “Back-to-Basics Tutorial: X-Ray Diffraction of Thin Films
,” J. Electroceram.
, 47
(4
), pp. 141
–163
. 31.
Lari Baghal
, S. M.
, Amadeh
, A.
, Heydarzadeh Sohi
, M.
, and Hadavi
, S. M. M.
, 2013
, “The Effect of SDS Surfactant on Tensile Properties of Electrodeposited Ni–Co/SiC Nanocomposites
,” Mater. Sci. Eng. A
, 559
, pp. 583
–590
. 32.
Liu
, P.
, Chen
, D.
, Wang
, Q.
, Xu
, P.
, Long
, M.
, and Duan
, H.
, 2020
, “Crystal Structure and Mechanical Properties of Nickel–Cobalt Alloys With Different Compositions: A First-Principles Study
,” J. Phys. Chem. Solids
, 137
, p. 109194
. 33.
Wu
, B. Y. C.
, Schuh
, C. A.
, and Ferreira
, P. J.
, 2005
, “Nanostructured Ni–Co Alloys With Tailorable Grain Size and Twin Density
,” Metall. Mater. Trans. A
, 36
(7
), pp. 1927
–1936
. 34.
Bull
, S. J.
, 1991
, “Failure Modes in Scratch Adhesion Testing
,” Surf. Coat. Technol.
, 50
(1
), pp. 25
–32
. 35.
Bull
, S. J.
, 1997
, “Failure Mode Maps in the Thin Film Scratch Adhesion Test
,” Tribol. Int.
, 30
(7
), pp. 491
–498
. 36.
Sundararaman
, D.
, 1995
, “Nanocrystalline State and Solid State Amorphization
,” Mater. Sci. Eng. B
, 32
(3
), pp. 307
–313
. 37.
Blau
, P. J.
, 2005
, “On the Nature of Running-In
,” Tribol. Int.
, 38
(11–12
), pp. 1007
–1012
. 38.
Davim
, J. P.
, and Davim
, J. P.
, eds., 2011
, Tribology for Engineers: A Practical Guide
, Elsevier
, New York
.39.
Suh
, N. P.
, 1977
, “An Overview of the Delamination Theory of Wear
,” Wear
, 44
(1
), pp. 1
–16
. 40.
Zhang
, Y.
, Kang
, M.
, Yao
, L.
, Mbugua
, N. S.
, Jin
, M.
, and Zhu
, J.
, 2020
, “Study on the Wear and Seawater Corrosion Resistance of Ni–Co–P Alloy Coatings With Jet Electrodeposition in Different Jet Voltages and Temperatures of Plating Solution
,” Coatings
, 10
(7
), p. 639
. 41.
Dahmani
, K.
, Galai
, M.
, Ech-Chebab
, A.
, Al-Zaqri
, N.
, Ouakki
, M.
, Elgendy
, A.
, Ez-Zriouli
, R.
, Kim
, S. C.
, Touhami
, M. E.
, and Cherkaoui
, M.
, 2023
, “Investigating the Inhibitory Properties of Cupressus Sempervirens Extract Against Copper Corrosion in 0.5 M H2SO4: Combining Quantum (Density Functional Theory Calculation–Monte Carlo Simulation) and Electrochemical-Surface Studies
,” ACS Omega
, 8
(27
), pp. 24218
–24232
. 42.
Srivastava
, M.
, Selvi
, V. E.
, Grips
, V. W.
, and Rajam
, K. S.
, 2006
, “Corrosion Resistance and Microstructure of Electrodeposited Nickel–Cobalt Alloy Coatings
,” Surf. Coat. Technol.
, 201
(6
), pp. 3051
–3060
. 43.
Bakhit
, B.
, and Akbari
, A.
, 2013
, “Nanocrystalline Ni–Co Alloy Coatings: Electrodeposition Using Horizontal Electrodes and Corrosion Resistance
,” J. Coat. Technol. Res.
, 10
(2
), pp. 285
–295
. 44.
Lian
, K. K.
, and Birss
, V. I.
, 1991
, “Hydrous Oxide Film Growth on Amorphous Ni–Co Alloys
,” J. Electrochem. Soc.
, 138
(10
), p. 2877
. 
