An experimental investigation was conducted on the internal flowfield of a simulated smooth-wall turbine blade cooling passage. The square cross-sectioned passage was manufactured from quartz for optical accessibility. Velocity measurements were taken using Particle Image Velocimetry for both heated and non-heated cases. Thin film resistive heaters on all four exterior walls of the passage allowed heat to be added to the coolant flow without obstructing laser access. Under the same conditions, an infrared detector with associated optics collected wall temperature data for use in calculating local Nusselt number. The test section was operated with radial outward flow and at values of Reynolds number and Rotation number typical of a small turbine blade. The density ratio was 0.27. Velocity data for the non-heated case document the evolution of the Coriolis-induced double vortex. The vortex has the effect of disproportionately increasing the leading side boundary layer thickness. Also, the streamwise component of the Coriolis acceleration creates a considerably thinned side wall boundary layer. Additionally, these data reveal a highly unsteady, turbulent flowfield in the cooling passage. Velocity data for the heated case show a strongly distorted streamwise profile indicative of a buoyancy effect on the leading side. The Coriolis vortex is the mechanism for the accumulation of stagnant flow on the leading side of the passage. Heat transfer data show a maximum factor of two difference in the Nusselt number from trailing side to leading side. A first-order estimate of this heat transfer disparity based on the measured boundary layer edge velocity yields approximately the same factor of two. A momentum integral model was developed for data interpretation, which accounts for coriolis and buoyancy effects. Calculated streamwise profiles and secondary flows match the experimental data well. The model, the velocity data, and the heat transfer data combine to strongly suggest the presence of separated flow on the leading wall starting at about five hydraulic diameters from the channel inlet for the conditions studied.

Issue Section:
Research Papers
Topics:
Cooling, Heat transfer, Flow (Dynamics), Boundary layers, Vortices, Buoyancy, Turbine blades, Coolants, Density, Exterior walls, Heat, Lasers, Momentum, Optics, Particulate matter, Quartz, Reynolds number, Rotation, Sensors, Thin films, Turbulence, Velocity measurement, Wall temperature
1.
Barry, P., 1994, “Rotational Effects on Turbine Blade Cooling,” Master’s Thesis, Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, Cambridge, MA.
2.
Berg, H., Hennecke, D., Elfert, M., and Hein, O., 1991, “The Effect of Rotation on Local Coolant Side Flow and Heat Transfer in Turbine Blades,” ISABE 91-7016, published by AIAA, pp. 170–183.
3.
Bonhoff, B., Tomm, U., Johnson, B., and Jennions, I., 1997, “Heat Transfer Predictions for Rotating U-Shaped Coolant Channels With Skewed Ribs and With Smooth Walls,” ASME Paper No. 97-GT-162.
4.
Bons, J., 1997, “Complementary Velocity and Heat Transfer Measurements in a Rotating Turbine Cooling Passage,” PhD Thesis, Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, Cambridge, MA.
5.
Boussinesq, X. X., 1930, Theorie Analytique de la Chaleur, Vol. 2, Gathiers-Villars, Paris.
6.
Boyer, D. L., 1965, “Flow Through a Rapidly Rotating Rectangular Channel,” PhD Thesis, The Johns Hopkins University.
7.
Bryanston-Cross
P.
, and
Epstein
A.
,
1990
, “
The Application of Sub-micron Particle Visualisation for PIV at Transonic and Supersonic Speeds
,”
Prog. Aerospace Sci.
, Vol.
27
, pp.
237
–
265
.
8.
Chew
J.
,
1993
, “
A Momentum-Integral Solution of Flow in a Rotating Circular Duct
,”
Int. J. Heat Fluid Flow
, Vol.
14
, No.
3
, pp.
240
–
245
.
9.
Dittus, F. W., and Boelter, L. M. K., 1930, University of California Publications, Vol. 2, p. 443.
10.
Dutta, S., Andrews, M., and Han, J. C., 1994, “Numerical Prediction of Turbulent Heat Transfer in a Rotating Square Duct With Variable Rotational Buoyancy Effects,” presented at the 6th AIAA/ASME Thermophysics and Heat Transfer Conference, Colorado Springs, CO, June 20–23.
11.
Guidez
J.
,
1989
, “
Study of the Convective Heat Transfer in a Rotating Coolant Channel
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
111
, pp.
43
–
50
.
12.
Han
J.
, and
Zhang
Y.
,
1992
, “
Effect of Uneven Wall Temperature on Local Heat Transfer in a Rotating Square Channel With Smooth Walls and Radial Outward Flow
,”
ASME Journal of Heat Transfer
, Vol.
114
, pp.
850
–
858
.
13.
Han
J.
,
Zhang
Y.
, and
Lee
C.
,
1994
, “
Influence of Surface Heating Condition on Local Heat Transfer in a Rotating Square Channel With Smooth Walls and Radial Outward Flow
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
116
, pp.
149
–
158
.
14.
Hsieh, S., Chiang, M., and Chen, P., 1997, “Velocity Measurements and Local Heat Transfer in a Rotating Ribbed Two-Pass Square Channel With Uneven Wall Heat Flux,” ASME Paper No. 97-GT-160.
15.
Iacovides
H.
, and
Launder
B.
,
1991
, “
Parametric and Numerical Study of Fully Developed Flow and Heat Transfer in Rotating Rectangular Ducts
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
113
, pp.
331
–
338
.
16.
Ito, H., and Nanbu, K., 1971, “Flow in Rotating Straight Pipes of Circular Cross Sections,” ASME Journal of Basic Engineering, pp. 383–394.
17.
Jefferies, R. W., 1996, “Interactions of a Quasi-Two-Dimensional Vortex With a Stationary and Oscillating Leading-Edge,” PhD Thesis, Department of Mechanical Engineering, Lehigh University, PA.
18.
Kays, W., and Crawford, M., 1980, Convective Heat and Mass Transfer, McGraw-Hill, New York.
19.
Mochizuki
S.
,
Takamura
J.
,
Yamawaki
S.
, and
Yang
Wen-Jei
,
1994
, “
Heat Transfer in Serpentine Flow Passages with Rotation
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
116
, pp.
133
–
140
.
20.
Moore, J., 1967, “Effects of Coriolis on Turbulent Flow in Rotating Rectangular Channels,” Gas Turbine Lab Report #89, Massachusetts Institute of Technology, Cambridge, MA.
21.
Mori
Y.
, and
Nakayama
W.
,
1968
, “
Convective Heat Transfer in Rotating Radial Circular Pipes (1st Report, Laminar Region)
,”
International Journal of Heat and Mass Transfer
, Vol.
11
, pp.
1027
–
1040
.
22.
Morris
W.
, and
Ayhan
T.
,
1979
, “
Observations on the Influence of Rotation on Heat Transfer in the Coolant Channels of Gas Turbine Rotor Blades
,”
Proc. Inst. Mech. Engrs.
, Vol.
193
, pp.
303
–
311
.
23.
Morris, W., 1981, Heat Transfer and Fluid Flow in Rotating Coolant Channels, Research Studies Press.
24.
Morris
W.
, and
Ghavami-Nasr
G.
,
1991
, “
Heat Transfer Measurements in Rectangular Channels With Orthogonal Mode Rotation
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
113
, pp.
339
–
345
.
25.
Prakash
C.
, and
Zerkle
R.
,
1992
, “
Prediction of Turbulent Flow and Heat Transfer in a Radially Rotating Square Duct
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
114
, pp.
835
–
846
.
26.
Tekriwal, P., 1996, “Effect of Aspect Ratio on the Buoyancy Driven Reverse Flow Near the Leading Wall of Rotating Cooling Passages,” ASME Paper No. 96-GT-173.
27.
Tekriwal, P., 1994, “Heat Transfer Predictions in Rotating Radial Smooth Channel: Comparative Study of k-e Models With Wall Function and Low-Re Model,” ASME Paper No. 94-GT-196.
28.
Tse, D., and McGrath, D., 1995, “A Combined Experimental/Computational Study of Flow in Turbine Blade Passage: Part I—Experimental Study,” ASME Paper No. 95-GT-355.
29.
Tse, D., and Steuber, G., 1997, “Flow in a Rotating Square Serpentine Coolant Passage With Skewed Trips,” ASME Paper No. 97-GT-529.
30.
Uellner, S., and Roesner, K., 1991, “LSV Applied to the Flow in a Rotating Channel,” Laser Anemometry: Advances and Applications—1991, Vol. 2, ASME, pp. 541–546.
31.
Wagner
J.
,
Johnson
B.
, and
Hajek
T.
,
1991
a, “
Heat Transfer in Rotating Passages With Smooth Walls and Radial Outward Flow
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
113
, pp.
42
–
51
.
32.
Wagner
J.
,
Johnson
B.
, and
Kopper
F.
,
1991
b, “
Heat Transfer in Rotating Serpentine Passages With Smooth Walls
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
113
, pp.
321
–
330
.
33.
Wagner
J.
,
Johnson
B.
,
Graziani
R.
, and
Yeh
F.
,
1992
, “
Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
114
, pp.
847
–
856
.
34.
Wagner, R., and Velkoff, H., 1972, “Measurements of Secondary Flows in a Rotating Duct,” ASME Journal of Engineering for Power, pp. 261–270.
This content is only available via PDF.
Copyright © 1999
 by The American Society of Mechanical Engineers
You do not currently have access to this content.