Calculations were performed to assess the effect of the tip leakage flow on the rate of heat transfer to blade, blade tip, and casing. The effect on exit angle and efficiency was also examined. Passage geometries with and without casing recess were considered. The geometry and the flow conditions of the GE-E3 first-stage turbine, which represents a modern gas turbine blade, were used for the analysis. Clearance heights of 0, 1, 1.5, and 3 percent of the passage height were considered. For the two largest clearance heights considered, different recess depths were studied. There was an increase in the thermal load on all the heat transfer surfaces considered due to enlargement of the clearance gap. Introduction of recessed casing resulted in a drop in the rate of heat transfer on the pressure side, but the picture on the suction side was found to be more complex for the smaller tip clearance height considered. For the larger tip clearance height, the effect of casing recess was an orderly reduction in the suction side heat transfer as the casing recess height was increased. There was a marked reduction of heat load and peak values on the blade tip upon introduction of casing recess; however, only a small reduction was observed on the casing itself. It was reconfirmed that there is a linear relationship between the efficiency and the tip gap height. It was also observed that the recess casing has a small effect on the efficiency but can have a moderating effect on the flow underturning at smaller tip clearances.

Issue Section:
Research Papers
Topics:
Clearances (Engineering), Heat transfer, Turbines, Blades, Flow (Dynamics), Stress, Suction, Gas turbines, Geometry, Heat, Leakage flows, Pressure
1.
Ameri, A. A., and Steinthorrson, E., 1995, “Prediction of Unshrouded Rotor Blade Tip Heat Transfer,” ASME Paper No. 95-GT-142.
2.
Ameri, A. A., and Steinthorrson, E., 1996, “Analysis of Gas Turbine Rotor Blade Tip and Shroud Heat Transfer,” ASME Paper No. 96-GT-189.
3.
Ameri
A. A.
,
Steinthorsson
E.
, and
Rigby
D. L.
,
1998
, “
Effect of Squealer Tip on Rotor Heat Transfer and Efficiency
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
120
, pp.
753
–
759
.
4.
Boyle
R. J.
,
Haas
J. E.
, and
Katsanis
T.
,
1985
, “
Comparison Between Measured Turbine Stage Performance and the Predicted Performance Using Quasi-3D Flow and Boundary Layer Analyses
,”
J. Propulsion Power
, Vol.
1
, No.
3
, pp.
242
–
251
.
5.
Briley, W. R., Roscoe, D. V., Gilbeling, H. J., Buggeln, R. C., and Sabnis, J. S., 1991, “Computation of Flow Past a Turbine Blade With and Without Tip Clearance,” ASME Paper No. 91-GT-56.
6.
Epstein, A. H., Guenette, G. R., Norton, R. J. G., and Cao Yuzhang, 1985, “Time Resolved Measurements of a Turbine Rotor Stationary Tip Casing Pressure and Heat Transfer Field,” AIAA Paper No. 85-1220.
7.
Garg, V. K., and Rigby, D. L., 1998, “Heat Transfer on a Film-Cooled Blade-Effect of Hole Physics,” ASME Paper No. 98-GT-404.
8.
Glassman, A. J., 1994, Turbine Design and Application, NASA SP-290.
9.
Haas, J. F., and Kofsky, M. G., 1979, “Effect of Rotor Tip Clearance and Configuration on Overall Performance of a 12.77-Centimeter Tip Diameter Axial-Flow Turbine,” NASA TM 79025.
10.
Halila, E. E., Lenahan, D. T., and Thomas, T. T., 1982, “Energy Efficient Engine, High Pressure Turbine Test Hardware Detailed Design Report,” NASA CR-167955.
11.
Hong, Yong S., and Groh, F. G., 1966, “Axial Turbine Loss Analysis and Efficiency Prediction Method,” Rep. D4-3220, Boeing Co., Mar. 11.
12.
Kaiser, I., and Bindon, P. J., 1997, “The Effect of Tip Clearance on the Development of Loss Behind a Rotor and a Subsequent Nozzle,” ASME Paper No. 97-GT-53.
13.
Menter, F. R., 1993, “Zonal Two-Equation k–ω Turbulence Models for Aerodynamic Flows,” Paper No. AIAA-93-2906.
14.
Metzger
D. E.
,
Bunker
R. S.
, and
Chyu
M. K.
,
1989
, “
Cavity Heat Transfer on a Transverse Grooved Wall in a Narrow Channel
,”
ASME Journal of Heat Transfer
, Vol.
111
, pp.
73
–
79
.
15.
Rigby, D. L., 1996, “Method of Weakest Descent for Automatic Block Merging,” Proc. 15th Int. Conf. on Num. Methods in Fluid Dynamics, Monterey, CA, June.
16.
Rigby, D. L., Ameri, A. A., and Steinthorsson, E., 1996, “Internal Passage Heat Transfer Prediction Using Multiblock Grids and k–ω Turbulence Model,” ASME Paper No. 96-GT-188.
17.
Rigby, D. L., Ameri, A. A., and Steinthorsson, E., 1997a, “Numerical Prediction of Heat Transfer in a Channel With Ribs and Bleed,” ASME Paper No. 97-GT-431.
18.
Rigby, D. L., Steinthorsson, E., and Coirier, W. J., 1997b, “Automatic Block Merging Using the Method of Weakest Descent,” AIAA Paper No. 97-0197.
19.
Schlichting, H., Boundary Layer Theory, 7th ed., McGraw-Hill, New York, pp. 312–313.
20.
Steinthorsson, E., Liou, M. S., and Povinelli, L. A., 1993, “Development of an Explicit Multiblock/Multigrid Flow Solver for Viscous Flows in Complex Geometries,” Paper No. AIAA-93-2380.
21.
Timko, L. P., 1982, “Energy Efficient Engine High Pressure Turbine Component Test Performance Report,” NASA CR-168289.
22.
Wilcox, D. C., 1994a, Turbulence Modeling for CFD, DCW Industries, Inc., La Canada, CA.
23.
Wilcox
D. C.
,
1994
b, “
Simulation of Transition With a Two-Equation Turbulence Model
,”
AIAA Journal
, Vol.
32
, No.
2
, pp.
247
–
255
.
This content is only available via PDF.
Copyright © 1999
 by The American Society of Mechanical Engineers
You do not currently have access to this content.