Centrifugal compressors used for turbochargers are required to have a wide operating range. A recirculation device, which consists of a bleed slot, an upstream slot, and an annular cavity connecting both slots, is often used with them. It improves the incidence angle of the impeller leading edge, i.e., the blade loading of the inducer, at low flow rates due to the recirculation flow supplied to the compressor inlet. However, the compressor efficiency drops when there is a recirculation flow from the bleed slot to the upstream slot. A one dimensional analysis in the first section of this paper showed that the reduction in the compressor efficiency can be lowered by decreasing the pressure drop or reducing the recirculation flow rate within the recirculation device. This study examined the possibility of improvement in the compressor efficiency by the use of a recirculation device with an asymmetric bleed slot. An impeller of a turbocharger compressor is normally contained in a volute. Since the geometry of the volute is not axisymmetric, the impeller is surrounded by an asymmetric flow field. Hence each impeller passage, which is formed by two adjacent full blades, is operated at a different operating point. This means that some of the passages need the improvement in the blade loading by the recirculation device but others do not. There is a possibility that this is realized by a recirculation device with an asymmetrically distributed bleed slot, called a nonaxisymmetric recirculation device in this paper. If the asymmetric bleed slot shortens the average distance between the bleed slot and upstream slot or reduces the area of the bleed slot, it can reduce the pressure drop or recirculation flow rate within the recirculation deviceand, hence, can improve the compressor efficiency. This study discusses the characteristics of high pressure ratio compressors for turbochargers without the recirculation device and those with the recirculation device with an axisymmetric bleed slot. Furthermore, the effects of nonaxisymmetric recirculation devices on the compressor characteristics are experimentally investigated. Two types of nonaxisymmetric recirculation devices were tested. One had the bleed slot of a sine wave pattern. The other had the bleed slot partially channeled in the circumferential direction. There were appropriate positions relative to the volute for both nonaxisymmetric recirculation devices. The compressor efficiency with nonaxisymmetric recirculation devices was higher than that with axisymmetric recirculation devices and the surge lines of the compressor with nonaxisymmetric recirculation devices were located at a flow rate lower than or equal to those with the axisymmetric recirculation devices.

References

1.
Hunziker
,
R.
,
Dickmann
H.-P.
, and
Emmrich
,
R.
,
2001
, “
Numerical and Experimental Investigation of a Centrifugal Compressor With an Inducer Casing Bleed System
,”
Proc. Inst. Mech. Eng., Part A.
,
215
, pp.
783
791
.10.1243/0957650011538910
2.
Sivagnanasundaram
,
S.
,
Spence
,
S.
,
Early
,
J.
, and
Nikpour
,
B.
,
2010
, “
An Investigation of Compressor Map Width Enhancement and the Inducer Flow Field Using Various Configurations of Shroud Bleed Slot
,”
ASME
Paper No. GT2010-22154.10.1115/GT2010-22154
3.
Cumpsty
,
N. A.
,
1989
,
Compressor Aerodynamics
,
Longman Scientific & Technical
, Harlow, UK, pp.
303
309
.
4.
Whitfield
,
A.
and
Baines
,
N. C.
,
1990
,
Design of Radial Turbomachines
,
Longman Scientific & Technical
, Harlow, UK, pp.
131
134
.
5.
Fink
,
D. A.
,
Cumpsty
,
N. A.
, and
Greitzer
,
E. M.
,
1992
, “
Surge Dynamics in a Free-Spool Centrifugal Compressor System
,”
ASME J. Turbomach.
,
114
(
2
), pp.
321
332
.10.1115/1.2929146
6.
Fisher
,
F. B.
,
1988
, “
Application of Map Width Enhancement Devices to Turbocharger Compressors Stages
,”
SAE
Paper No. 88079410.4271/880794.
7.
Zheng
,
X.
,
Zhang
,
J.
,
Bamba
,
T.
,
Tamaki
,
H.
, and
Yang
,
M.
,
2010
, “
Stability Improvement by High-Pressure-Ratio Turbocharger Centrifugal Compressor by Asymmetric Flow Control: Part II—Non-Axisymmetric Self-Recirculation-Casing-Treatment
,”
ASME
Paper No. GT2010-22582.10.1115/GT2010-22582
8.
Yang
,
M.
,
Martinez-Botas
,
R.
,
Zhang
,
Y.
,
Zheng
,
X.
,
Tamaki
,
H.
,
Bamba
,
T.
, and
Li
,
Z.
,
2011
, “
Investigation of Self-Recycling-Casing-Treatment (SRCT) Influence on Stability of High Pressure Ratio Centrifugal Compressor With a Volute
,”
ASME
Paper No. GT2011-4506510.1115/GT2011-45065.
9.
Yang
,
M.
,
Zheng
,
X.
,
Zhang
,
J.
,
Bamba
,
T.
,
Tamaki
,
H.
,
Huenteler
,
J.
, and
Li
,
Z.
,
2010
, “
Stability Improvement by High-Pressure-Ratio Turbocharger Centrifugal Compressor by Asymmetric Flow Control: Part I—Non-Axisymmetric Flow in Centrifugal Compressor
,”
ASME
Paper No. GT2010-22581.10.1115/GT2010-22581
10.
Tamaki
,
H.
,
Unno
,
M.
,
Kawakubo
,
T.
, and
Hirata
,
Y.
,
2009
, “
Aerodynamic Design to Increase Pressure Ratio of Centrifugal Compressors for Turbochargers
,”
ASME
Paper No. GT2009-59160.10.1115/GT2009-59160
11.
Tamaki
,
H.
,
2012
, “
Effect of Recirculation Device With Counter Swirl Vane on Performance of High Pressure Ratio Centrifugal Compressor
,”
ASME J. Turbomach.
,
134
, p.
051036
.10.1115/1.4004820
You do not currently have access to this content.