This paper is to develop a unified algorithm to predict vibration of spinning asymmetric rotors with arbitrary geometry and complexity. Specifically, the algorithm is to predict vibration response of spinning rotors from a ground-based observer. As a first approximation, the effects of housings and bearings are not included in this analysis. The unified algorithm consists of three steps. The first step is to conduct a finite element analysis on the corresponding stationary rotor to extract natural frequencies and mode shapes. The second step is to represent the vibration of the spinning rotor in terms of the mode shapes and their modal response in a coordinate system that is rotating with the spinning rotor. The equation of motion governing the modal response is derived through use of the Lagrange equation. To construct the equation of motion, explicitly, the results from the finite element analysis will be used to calculate the gyroscopic matrix, centrifugal stiffening (or softening) matrix, and generalized modal excitation vector. The third step is to solve the equation of motion to obtain the modal response, which, in turn, will lead to physical response of the rotor for a rotor-based observer or for a ground-based observer through a coordinate transformation. Results of the algorithm indicate that Campbell diagrams of spinning asymmetric rotors will not only have traditional forward and backward primary resonances as in axisymmetric rotors, but also have secondary resonances caused by higher harmonics resulting from the mode shapes. Finally, the algorithm is validated through a calibrated experiment using rotating disks with evenly spaced radial slots. Qualitatively, all measured vibration spectra show significant forward and backward primary resonances as well as secondary resonances as predicted in the theoretical analysis. Quantitatively, measured primary and secondary resonance frequencies agree extremely well with those predicted from the algorithm with mostly difference.
Skip Nav Destination
Article navigation
June 2006
Technical Papers
A Linearized Theory on Ground-Based Vibration Response of Rotating Asymmetric Flexible Structures
I. Y. Shen,
I. Y. Shen
Professor
Department of Mechanical Engineering,
University of Washington
, Seattle, WA 98195-2600
Search for other works by this author on:
Hyunchul Kim
Hyunchul Kim
Graduate Student
Department of Mechanical Engineering,
University of Washington
, Seattle, WA 98195-2600
Search for other works by this author on:
I. Y. Shen
Professor
Department of Mechanical Engineering,
University of Washington
, Seattle, WA 98195-2600
Hyunchul Kim
Graduate Student
Department of Mechanical Engineering,
University of Washington
, Seattle, WA 98195-2600J. Vib. Acoust. Jun 2006, 128(3): 375-384 (10 pages)
Published Online: January 9, 2006
Article history
Received:
March 29, 2005
Revised:
January 9, 2006
Citation
Shen, I. Y., and Kim, H. (January 9, 2006). "A Linearized Theory on Ground-Based Vibration Response of Rotating Asymmetric Flexible Structures." ASME. J. Vib. Acoust. June 2006; 128(3): 375–384. https://doi.org/10.1115/1.2172265
Download citation file:
Get Email Alerts
Boundary-Element Analysis of the Noise Scattering for Urban Aerial Mobility Vehicles: Solver Development and Assessment
J. Vib. Acoust (October 2024)
Related Articles
A Unified Approach to Analyze Vibration of Axisymmetric Rotating Structures with Flexible Stationary Parts
J. Vib. Acoust (April,2005)
Component-Mode-Based Reduced Order Modeling Techniques for Mistuned Bladed Disks—Part II: Application
J. Eng. Gas Turbines Power (January,2001)
Simulation of Structural Deformations of Flexible Piping Systems by Acoustic Excitation
J. Pressure Vessel Technol (August,2007)
A Simple Technique for Maximizing the Fundamental Frequency of Vibrating Structures
J. Electron. Packag (December,2000)
Related Proceedings Papers
Related Chapters
Fluidelastic Instability of Tube Bundles in Single-Phase Flow
Flow-Induced Vibration Handbook for Nuclear and Process Equipment
Structural Damage Detection by Integrating Neural Networks and Vibration Modal Analysis
International Conference on Computer and Automation Engineering, 4th (ICCAE 2012)
Modal Analysis of Mechanical Vibrations
Engineering Practice with Oilfield and Drilling Applications